Something in the world of floating have you stumped?
Show Highlights
Today brings a curious question about a float center owner who’s trying to deal with salt dust everywhere, including in their tool room. While salt does get everywhere, it can’t evaporate like water can and doesn’t travel through the air very well.
Graham and Ashkahn try their best to answer it and try to figure out what might be causing it, having not experienced something like that themselves at Float On. If any float centers out there have experienced this phenomenon and have any insights, send it our way!
Listen to Just the Audio
Transcription of this episode… (in case you prefer reading)
Graham: Today’s question is, “What about the phenomena of evaporation resulting in salt residue everywhere? Anyone else have this? Do you have to clean out the HVAC system? We found that some of the tools rust just from the salt in the air. Just from the salt in the air.”
Ashkahn: Just from the salt in the tools, like in their tool room?
Graham: Yeah, it seems like a long way for-
Ashkahn: This is-
Graham: … salt air to travel.
Ashkahn: So, like, this doesn’t really happen to us. Like, I don’t notice in our float rooms, like, salt building up on the ceilings or in the HVAC vents or-
Graham: No, except from people doing the Herbal Essences kind of hair flip when they get out of a float tank. We really don’t find salt just kind of coating things, as though it had been aerated or anything like that.
Ashkahn: Yeah, it’s not like a powder or salt or, yeah. Even on the ceilings of the float tanks, there’s not like a fine dusting of salt or anything.
Graham: Yeah.
Ashkahn: But I guess it is like, it can be very humid, too, in there.
Graham: Yeah, I mean. So I see, you know, when I’ve heard of people that experience rust problems or issues with HVAC vents and things like that, it almost always in talking to them and working through things, ends up being more related to the moisture in the air than actually having salts in the air that’s getting in there. And if the HVAC installers didn’t prepare for the sheer volume of humidity that your float tanks can crank out, then yeah, you can totally hit problems in those vents and in the system as a whole.
Ashkahn: That’s good. I would ask these people that question. Like, are you-
Graham: Are you sure it’s salt or could it be-
Ashkahn: Are you actually seeing salt. ‘Cause if it’s salt, you’d see salt building up on things.
Graham: They see the salt residue everywhere is a direct quote from the question.
Ashkahn: Salt residue everywhere, that’s so strange.
Graham: I mean, so, I can think of a couple things. And from our consulting, I’ve probably heard of things like this a couple times. But, I mean, much more I hear people who are surprised that they don’t see salt getting everywhere.
Ashkahn: Right.
Graham: You know, they expect it to be like the ocean.
Ashkahn: Right.
Graham: Where the ocean is so turbulent, and it’s just kicking up all of these waves and this water.
Ashkahn: Some mist, a sea mist.
Graham: If you drive a car anywhere near the ocean, you just know your car has to be coated or it’s going to rust out from the bottom, and every metal part is going … So, I think people picture that with a float tank center, and are surprised when they open to find that’s actually not the case, which again in Float On, for us, it certainly has not been. So, the couple things I can think of are, if you have something, even like a pinhole leak in your filtration system, there’s a chance that you can be kind of spraying a really fine salt spray around. It’s almost like installer error or something going wrong with the pump system.
Ashkahn: Yeah. Like, I feel like even without any noticeable leaks, I’ve never seen a filtration system that doesn’t just kind of end up getting kind of salty.
Graham: Sure. And most of the time it’s from leaks, but sometimes there is kind of like a fine …
Ashkahn: Like a fine, fine mist of-
Graham: And I guess the most I’ve seen for a fine dust, is a couple of our tanks have …
Ashkahn: Right.
Graham: There is something about their filtration system… but only around the pump area leave this kind of residue. So, I wonder what could go wrong that would just sort of do that same vaporization.
Ashkahn: Get it everywhere?
Graham: Or really spread that to your work. All the way to where your tools are?
Ashkahn: Well, it’s so … Here’s the thing though. I feel like we have had the rusting issue, like our door hinges have … we’ve had to replace those with stainless steel door hinges.
Graham: Right, and yeah. Yeah, yeah.
Ashkahn: So, that’s … but there was no coating of salt on those things like there was or is in our pump areas, and under the pump boxes. So, it leads me to believe what you were saying, that it’s a moisture thing, not a salt thing, right?
Graham: Or that some … whenever you’re in a float room, there’s a chance again, someone’s just shaking out like a dog and getting salt everywhere. They put their salty hands on the-
Ashkahn: Or this is the door hinges of our front door I’m talking about.
Graham: Oh, I see. I thought you meant of the float room doors.
Ashkahn: So, that’s beyond like Herbal Essence range. We’re talking like lobby, front door door hinges, we needed to replace those things, too.
Graham: I was trying to picture situations where people go and shake off specifically near door hinges. I think I’ll concede this point. I think you win this one, yeah.
Ashkahn: But it is, you know, at times unbelievably humid in our lobby.
Graham: Oh yeah, I mean, even with three different dehumidifiers in our lobby, it still gets up to 60%, 70% humidity during those transitions.
Ashkahn: And again, what I see when I saw those door hinges was not what I see when I lift up a pump cover and see like a fine coating of salt on some of the equipment.
Graham: Yeah, so we don’t know. We’re not sure what’s going on with your fine powder, but it is not a common phenomenon.
Ashkahn: No.
Graham: There may very well be other float centers out there. If you have this, definitely write in and let us know if you have theories about it or what tanks you’re using or what your setup is. But again, having talked to a lot of people that don’t have this problem, I would say it’s more the exception than something that you really need to be aware of going into this.
Ashkahn: Definitely.
Graham: So, thanks for the question, keeping us on our toes.
Ashkahn: Yeah.
Graham: And yeah, if you have more questions you want to try to stump us with, go to floattanksolutions.com/podcast
Recent Podcast Episodes
How to Handle Reopening? – DSP 310
If there’s one thing Ashkahn and Graham have learned, it’s reopening. Float On has had to shut down for repairs so many times over the years that they’ve got the process down to a science.
They share their secrets for making sure you have a full week after opening, build momentum, keep your members happy in the downtime and throw a kickin’ reopening party!
What Inspires your Marketing? – DSP 309
Graham and Ashkahn talk about what it’s like when inspiration strikes, how they chase their floaty muse to a solid marketing idea and form it into an actionable plan.
The reality is that it mostly involves a lot of listening and willingness to try, and fail at, new things. As with so many things, play to your strengths, focus on the things you’re passionate about and the rest is practice.
What’s Happening with the Float Conference Non-Profit – DSP 308
Ashkahn and Graham talk about how the Float Conference has been going since they handed off the reigns this year. Big decisions are still incoming, but there’s a lot of ways you can help out or get involved.
If you’d like to offer your help, services, or suggestions for the new Non-profit of the Float Conference, or if you’d just like updates to how it’s going and where it might be held next year, email conference@floathq.com, and the Conference will know to contact you.
VR in a Float Tank – DSP 307
While they haven’t tried it themselves, Ashkahn and Graham liberally distribute their opinions on the use of VR in float tanks and what they think might be better, using it before, after, or during a float.
How to do A/B Testing – DSP 306
A/B Testing is a method to compare one system against another. Most often, this is used to compare the performance of one version of a website to another in real time.
Graham and Ashkahn talk about A/B testing (or “the old onesie-twosies” as Ashkahn says) and how it can be used to improve a float center’s website.
Latest Blog Posts
I’ll Give you a Float Tuesday for a Massage Today: Floating & Bartering
Whoever said that you can’t get something for Nothing obviously never ran a float center. At Float On, we’ve used bartering as a creative means to meet a wide range of goals and needs. Even as I’m writing this, I’m sipping on coffee that we traded from a shop across...
Financing Your Float Center with Investors
In addition to an increase in bank loans, more and more float centers have been using investors in recent years to finance their operations. Every center’s earning potential varies greatly — but a well-run center with no surprise buildout costs (or re-buildout costs) can do very well for itself.
As a result, people with means (or general interest) are increasingly likely to consider having a financial stake in the float industry without the glorious headache of actually running a shop.
Float Conference Interview
In the midst of all of our blog writing and party planning, I sat down with Ashkahn Jahromi, cofounder of The Float Conference, Float On, and Float Tank Solutions with a few questions about the upcoming Float Conference aka #FloatCon for you social media savvy kids in Twitterland.
Take Part in the 2017 Float Industry Report
We’re gathering responses for our 2017 Industry Report through the end of June, and we once again need your help.
Please take a brief moment to answer a few questions about your float center (or future float center) – it may be easiest thing you can do to contribute to the growth of floatation around the world.
