Something in the world of floating have you stumped?
Show Highlights
Today brings a curious question about a float center owner who’s trying to deal with salt dust everywhere, including in their tool room. While salt does get everywhere, it can’t evaporate like water can and doesn’t travel through the air very well.
Graham and Ashkahn try their best to answer it and try to figure out what might be causing it, having not experienced something like that themselves at Float On. If any float centers out there have experienced this phenomenon and have any insights, send it our way!
Listen to Just the Audio
Transcription of this episode… (in case you prefer reading)
Graham: Today’s question is, “What about the phenomena of evaporation resulting in salt residue everywhere? Anyone else have this? Do you have to clean out the HVAC system? We found that some of the tools rust just from the salt in the air. Just from the salt in the air.”
Ashkahn: Just from the salt in the tools, like in their tool room?
Graham: Yeah, it seems like a long way for-
Ashkahn: This is-
Graham: … salt air to travel.
Ashkahn: So, like, this doesn’t really happen to us. Like, I don’t notice in our float rooms, like, salt building up on the ceilings or in the HVAC vents or-
Graham: No, except from people doing the Herbal Essences kind of hair flip when they get out of a float tank. We really don’t find salt just kind of coating things, as though it had been aerated or anything like that.
Ashkahn: Yeah, it’s not like a powder or salt or, yeah. Even on the ceilings of the float tanks, there’s not like a fine dusting of salt or anything.
Graham: Yeah.
Ashkahn: But I guess it is like, it can be very humid, too, in there.
Graham: Yeah, I mean. So I see, you know, when I’ve heard of people that experience rust problems or issues with HVAC vents and things like that, it almost always in talking to them and working through things, ends up being more related to the moisture in the air than actually having salts in the air that’s getting in there. And if the HVAC installers didn’t prepare for the sheer volume of humidity that your float tanks can crank out, then yeah, you can totally hit problems in those vents and in the system as a whole.
Ashkahn: That’s good. I would ask these people that question. Like, are you-
Graham: Are you sure it’s salt or could it be-
Ashkahn: Are you actually seeing salt. ‘Cause if it’s salt, you’d see salt building up on things.
Graham: They see the salt residue everywhere is a direct quote from the question.
Ashkahn: Salt residue everywhere, that’s so strange.
Graham: I mean, so, I can think of a couple things. And from our consulting, I’ve probably heard of things like this a couple times. But, I mean, much more I hear people who are surprised that they don’t see salt getting everywhere.
Ashkahn: Right.
Graham: You know, they expect it to be like the ocean.
Ashkahn: Right.
Graham: Where the ocean is so turbulent, and it’s just kicking up all of these waves and this water.
Ashkahn: Some mist, a sea mist.
Graham: If you drive a car anywhere near the ocean, you just know your car has to be coated or it’s going to rust out from the bottom, and every metal part is going … So, I think people picture that with a float tank center, and are surprised when they open to find that’s actually not the case, which again in Float On, for us, it certainly has not been. So, the couple things I can think of are, if you have something, even like a pinhole leak in your filtration system, there’s a chance that you can be kind of spraying a really fine salt spray around. It’s almost like installer error or something going wrong with the pump system.
Ashkahn: Yeah. Like, I feel like even without any noticeable leaks, I’ve never seen a filtration system that doesn’t just kind of end up getting kind of salty.
Graham: Sure. And most of the time it’s from leaks, but sometimes there is kind of like a fine …
Ashkahn: Like a fine, fine mist of-
Graham: And I guess the most I’ve seen for a fine dust, is a couple of our tanks have …
Ashkahn: Right.
Graham: There is something about their filtration system… but only around the pump area leave this kind of residue. So, I wonder what could go wrong that would just sort of do that same vaporization.
Ashkahn: Get it everywhere?
Graham: Or really spread that to your work. All the way to where your tools are?
Ashkahn: Well, it’s so … Here’s the thing though. I feel like we have had the rusting issue, like our door hinges have … we’ve had to replace those with stainless steel door hinges.
Graham: Right, and yeah. Yeah, yeah.
Ashkahn: So, that’s … but there was no coating of salt on those things like there was or is in our pump areas, and under the pump boxes. So, it leads me to believe what you were saying, that it’s a moisture thing, not a salt thing, right?
Graham: Or that some … whenever you’re in a float room, there’s a chance again, someone’s just shaking out like a dog and getting salt everywhere. They put their salty hands on the-
Ashkahn: Or this is the door hinges of our front door I’m talking about.
Graham: Oh, I see. I thought you meant of the float room doors.
Ashkahn: So, that’s beyond like Herbal Essence range. We’re talking like lobby, front door door hinges, we needed to replace those things, too.
Graham: I was trying to picture situations where people go and shake off specifically near door hinges. I think I’ll concede this point. I think you win this one, yeah.
Ashkahn: But it is, you know, at times unbelievably humid in our lobby.
Graham: Oh yeah, I mean, even with three different dehumidifiers in our lobby, it still gets up to 60%, 70% humidity during those transitions.
Ashkahn: And again, what I see when I saw those door hinges was not what I see when I lift up a pump cover and see like a fine coating of salt on some of the equipment.
Graham: Yeah, so we don’t know. We’re not sure what’s going on with your fine powder, but it is not a common phenomenon.
Ashkahn: No.
Graham: There may very well be other float centers out there. If you have this, definitely write in and let us know if you have theories about it or what tanks you’re using or what your setup is. But again, having talked to a lot of people that don’t have this problem, I would say it’s more the exception than something that you really need to be aware of going into this.
Ashkahn: Definitely.
Graham: So, thanks for the question, keeping us on our toes.
Ashkahn: Yeah.
Graham: And yeah, if you have more questions you want to try to stump us with, go to floattanksolutions.com/podcast
Recent Podcast Episodes
When should you call it quits? – DSP 94
Deciding when to close down is a challenge in any business, but it can hit especially hard for a float center. The upfront costs to build out are much higher than other industries, many of which simply cannot be recouped. When do you decide that it’s time to cut your losses and move on? What expenses can you recoup?
Graham and Ashkahn tackle this difficult question with laying out some sensible guidelines about what it means to run a business and how to go about it in a way that makes you comfortable.
Leaving a tank unattended for a week – DSP 93
Float tanks are like giant salty babies sometimes. Between water sanitation, temperature control, and filtration…they require a lot of attention and care, and even when you do things perfectly they can still make giant salty messes everywhere. So how do you leave your baby alone for a week? How do you prepare for that? Unlike a human baby, you can take your float tank with you (or at least it’s unlikely).
Choosing a Shower Disinfectant for your float center – DSP 92
A recommendation for a shower cleaner should be a fairly straightforward answer, right? Well… maybe not. Graham and Ashkahn are very particular about the definitions of things like “sanitation” “disinfectant” and other common cleaning terms. In this episode, they take the time to explain what product labels typically mean and what you want to look for when getting a surface cleaner for your float center.
Be ready to dive in and do some extra reading when getting into this episode. There’s a lot of terminology to parse and clarify. Fortunately, it’s Graham and Ashkahn so they have lots of really clear advice, like “don’t mix bleach and ammonia (or any homemade cleaning product, really)”.
When Does a Float Start? – DSP 91
Time management and maintaining your schedule is one of the most important quality controls in a float center. If you can’t get people out on time, it can throw off your schedule for the rest of the day. So, when does a float start? How do you measure that time? And what do you do if a floater starts late? Cut off their float? The next persons?
Graham and Ashkahn have been running Float On in a particular way for a long time now, and have particular insights into the challenges of how you manage your schedule.
Tips for filling an empty service schedule – DSP 90
There are fewer things more stress inducing for a float center than seeing their schedule for the week and having it just be completely empty (Maybe watching your pump start up and spray water over your entire float room, but it’s a close call). What do you do in that situation? And how do you prevent it from happening in the future?
Well, Graham and Ashkahn have tried everything, from doing shout outs and deals on social media, to literally walking down the street trying to convince people to come in and float while the tanks were empty. Some tactics are more effective than others, but what it really comes down, at least in Float On’s case, is being prepared to give out a ton of free floats.
The guys talk about the effectiveness of each strategy they’ve tried and how they’ve reached out to contacts to form mutually beneficial business relationships and really get the ball rolling with filling up their tanks.
Latest Blog Posts
No Results Found
The page you requested could not be found. Try refining your search, or use the navigation above to locate the post.
