Something in the world of floating have you stumped?
Show Highlights
Soon after you open, you might realize that you’ve gotten a lot of the same complaint: The float was great, but I heard all this rumbling.
Odds are, your floaters are hearing one of two things — traffic on the road outside or their very hungry tummy.
If it’s the latter, feed them some post float snacks and tea. If the former, what can you do?
Aside from difficult and expensive projects, like building new walls or lobbying for the removal of cars from municipal streets, it turns out there are some pretty simple and cheap solutions that will block traffic noise.
Like inexpensive rubber pucks.
Pucks?
Puck yeah. Listen above or read below to learn more.
Show Resources
Listen to Just the Audio
Transcription of this episode… (in case you prefer reading)
Ashkahn: Alright, what’s our question today?
Graham: Alright, our question today is, “Help, I’ve just opened but I’m getting at least a couple of complaints a day about sound in the tanks, probably from traffic. What are my options?”
Ashkahn: Traffic sound, huh?
Graham: The old traffic sound. An oldie but a goodie.
Ashkahn: Yeah, so there are some options, that’s the nice thing. They range from the basic to the extreme.
Graham: Yep. Basic is just, tear down your entire center, rebuild it somewhere else-
Ashkahn: Start over.
Graham: Start from scratch.
Ashkahn: Start a new life. Change your name.
So probably where I would start is vibration isolation pads, because that’s the cheapest and an option that doesn’t alter your building.
Graham: So here’s the deal: If you’re hearing traffic noise inside your float tank and your float tank isn’t already sitting on top of some kind of acoustical dampener, then you have a really easy solution that is very likely to eliminate most of that traffic noise coming in, which is great. And that’s what Ashkahn said, which is the vibration isolation pads. Or vibration isolation mat.
At Float On, we tend to prefer the pads because you have less points of contact with the ground, which we’ll get into when we explain these. But basically there’s varying levels of degree that you can go to to soundproof vibration coming in to your float tank from the floor.
Ashkahn: These things are, first of all, not that expensive. We usually use the three by three inch pucks. We’ll put —how many of those under a tank?
Graham: About 11.
Ashkahn: So, we’ll put 11 of those under a tank. So you’re talking about $33. And then you also need to usually connect them to a rigid surface — usually what we use is a plastic material, high density polyethylene, or an HTPE board.
Graham: I should say that’s opposed to plywood or something like that. Eventually, that plywood will get damaged by salt water and just not be feasible anymore, so we’ve switched to using this plastic material.
Ashkahn: So you’re taking these vibration isolation pads, and I guess I’ll start with what they do. The whole idea is that they dampen vibration going into your float tank. They’re really made more for doing the kind of reverse of that. They’re made for putting under machinery that creates a lot of vibration, to stop the vibration from getting to the rest of the building. You’ll often see these on HVAC and stuff like that, big air conditioner units on a roof.
Graham: We stuck them underneath crazy shoe machines next door, when there was a shoe shop right next to Float On.
Ashkahn: But they’re basically these pucks that have alternating materials in layers. The ones we use just go rubber and then a layer of this kind of EVA plastic is what they call it, and another layer of rubber. And just because the sound has to move through those different densities of materials, it changes the sound wave every time it hits one of those places where it needs to shift densities. By doing that you’re kind of dispersing the sound, because sound waves don’t like having to continuously go through different layers like that.
Graham: And it’s actually amazing how well these eliminate vibration sound coming in, which I think is why Ashkahn and I jumped immediately to this as a solution when we heard the word traffic noise. The traffic noise that you’re hearing isn’t even the horns coming from outside, I can almost promise you.
Ashkahn: Yeah, it’s not the engines.
Graham: It’s this low rumble coming from, often, really big trucks, motorcycles. That deep bass that just kind of goes through the street and into your concrete foundation or wooden foundation, up into your tanks, is very difficult to block out by any other means than actually just trying to decouple your float tank from the floor and somehow reduce those vibrations before they make it up into it.
In addition to that, not only traffic, but those are in general the hardest noises to block out. There’s a chance that separate from the traffic noises coming in that make people acutely object, you might also just end up with a much more soundproof environment. It might be immediately noticeable, if you get these layers of vibration isolation pads under your tank, even just with the little background hums and things like that that you hear.
Ashkahn: So yeah, you basically get these, and like I said, they’re just three inch by three inch pucks. That means that when the whole float tank is sitting on just 11 of those, it’s not really touching the ground in that many spots, so just the least amount of surface area possible is also going to help reduce the vibrations that can actually go up and get into your float tank. But because there’s just a few of them, then they create these kind of points of all the weight just sitting on those certain points. Sometimes the base of the float tank or the fiberglass might not be quite strong enough to have all of it’s weight on just 11 small points like that, so we’ll take the pucks and we’ll attach them to a big sheet of HTPE, a kind of plastic material, and we’ll cut that to the size of the float tank and then the float tank will sit on top of that. That kind of distributes the weight over it, but it still means the whole float tank is only touching the ground on those points that are made up of these vibration isolation pads.
One important thing to not forget is that you have to do that to your filtration system too, because the sound’s always going to go through the weakest spot. So, if you have your whole float tanks sitting on vibration isolation pads, and it’s all doing great and nice, but your pump is sitting on the ground and your pump is connected straight into your float tank through a pipe, then the sound’s just going to through that way. So you kind of have to do the whole system.
Graham: It’s incredibly easy to spend a ridiculous amount of money on soundproofing and accomplish almost nothing. Again, having your pump sitting on the ground can just ruin all of the time that you’ve just spent putting that vibration isolation stand underneath your float tank.
Similarly, your float tank actually touching your walls is another one to avoid. So have your tanks sitting at least an inch off of your walls, on every side. That’s even true of things like cabin style tanks, where often times you’ll have the exterior paneling kind of butting up and making almost a solid surface. Even that you want to have sitting off the wall, and preferably only filled in with some silicone caulking, or something like that, to make the actual seamless edge. But anywhere where your float tank touches the wall, that’s another place where vibration can come up through your floor, through the studs, through the wall and directly into the float tank. You might find, even putting in a stand, if your float tank’s leaning against a wall, you still get that same traffic noise coming in.
Ashkahn: Yeah, so specifically dealing with traffic noise, this seems to be the solution that often does it for people. It’s not often that I’ll hear a float center does this and still has too much traffic noise. So if this doesn’t work, probably the next step would be just to go outside, buy a giant road closed sign and put it in the street, and just not let anybody drive down that street anymore.
Graham: The City tends to frown on that, but just throw the officials in a float tank and you’re good.
Alright, thanks for the question. We’ll talk to you all tomorrow.
Recent Podcast Episodes
How Hot is Too Hot in a Float Tank? – DSP 280
Graham goes solo again to discuss how people perceive temperature in the float tank.
This is an important issue specifically because of a few pieces of technical information that your average customer just isn’t going to know, largely how humidity impacts temperature, but also how easy it is to overheat in an incredibly humid environment.
Why Shouldn’t Float Rooms Have Cement Backer Board? – DSP 279
Graham goes solo today while awaiting Ashkahn’s return.
Graham takes a question about cement backer board and the reasons it should be avoided in a float room. It’s a dense episode. Real dense. More dense, in fact, than cement backer board.
What to do when People have Really Bad Floats – DSP 278
With Ashkahn still taking his post-conference vacation, Graham and Juliet talk about what it’s like to have unpleasant floats.
Juliet shares her perspective in dealing with her anxiety condition while floating and how it can sometimes hinder the experience. Graham approaches it as an owner as well as someone who’s never experienced those kinds of hindrances in the tank.
How do you Prepare for a Float? – DSP 277
Some people have special ways that they prepare for floating, and how it’s approached depends entirely on the person floating.
Graham and Juliet (Ashkahn’s still missing) talk about their different approaches to floating, whether it’s sneaking in to float whenever they can, or planning entire days around floating to make sure it goes off without a hitch, they share their perspectives.
How to Talk about Floating to those Unfamiliar with it – DSP 276
Ashkahn is gallivanting across Europe (probably), so Graham has Juliet on the podcast today.
The two of them talk about how to talk about floating, from the float center perspective, and the floater perspective, how much information is enough, and how much is too much. This is a spiel that every person in the float industry will have tons of practice on, so it’s important to have a good one.
Latest Blog Posts
Sleeping Bag Drive: Filling Float Tanks While Helping the Homeless
Sitting in our regular Float On marketing meeting, we were strategizing about our next free float giveaway, and we quickly switched the conversation to focus less on our own minor woes (ahem, first world problems) and more on how we can help those in need. Despite the fact that Portland had its warmest November of all time, temperatures plunged to all-time lows in December and January. The team came together and voted on the idea of holding a sleeping bag drive.
How Floating Helped Me Accept I Was Trans
“I’ve often heard strong advocates of floating question why people might have difficult floats, “what’s wrong with spending time alone with yourself?” When you love yourself, it’s easy to be alone with your thoughts – when you hate who you are and can’t understand why, it can be a nightmare.” – Juliet Tango Mylan
Accurate H2O2 Readings in Float Tanks – an Approved Test Kit
There’s some exciting news out there for anyone who is using hydrogen peroxide in their float tanks. Taylor Technologies, launching into a brilliant meta-testing endeavor, has tested their own H2O2 testing kits…in saturated epsom salt water! After only a year of them...
Center of the Cyclone Book Launch
Coincidence Control Publishing is pleased to announce the updated publishing of John C. Lilly’s Center of the Cyclone. Written by a researcher whose methods of self inquiry and exploration were before his time, this 45th anniversary edition, released on Lilly’s birthday, is due to see the light of day once more.
You can buy the book now on Amazon!
