Something in the world of floating have you stumped?
Show Highlights
In this episode, Graham and Ashkahn share their expert opinion on… bubbles.
Not just any bubbles, but the ones that you sometimes find in a tank while you’re floating. What causes that?
Show Resources
Listen to Just the Audio
Transcription of this episode… (in case you prefer reading)
Graham: Our question for today is: “lately, I’ve noticed small bubbles tickling me during my floats. They also seem to be forming on the floor of the tank. What is going on?”
Ashkahn: What is going on, huh?
Graham: Alright, well, “Bubbly in the U.S.” We’ve got a solution for you.
Ashkahn: We sure do. It sounds, to me, like you’re using hydrogen peroxide.
Graham: If I were to guess, I would say the same thing. Or, you’ve got an aerator hooked in to the bottom of your tank.
Ashkahn: Yeah. Which I suspect, it’s not the second one.
Graham: I’ve never seen that ever in my life before.
Ashkahn: Are you in a jacuzzi and not a float tank? Is that what’s going on here? Basically, hydrogen peroxide breaks down into oxygen and water when it’s reacting with stuff. If you have a lot of hydrogen peroxide in your float tank, you might start being able to actually notice those … the air being created from that breakdown process of the peroxide. That’s, basically, what you’re feeling. You’re feeling tiny, air bubbles from the hydrogen peroxide.
Graham: And, for us, we end up getting that effect in our float tanks when we get above or around 100 parts per million.
Ashkahn: Yeah, somewhere in that … like 100, 110. That’s the range where we start to notice the bubble issue.
Graham: That’s as measure by the old Taylor Drop Test Kit, K-1826.
Ashkahn: Which, has been verified to be accurate in float tank water.
Graham: Which, you can look up. Taylor Labs actually tested our float water after we harassed them for a long time. You might find that those parts per million are different if you’re using test strips, or something else. Also, if you are, I highly recommend switching over to the old K-1826.
Ashkahn: Basically, that. Just don’t put your peroxide to those levels. Drop lower than that, and you won’t see those bubbles.
Graham: And that said, I still, occasionally, get bubbles, even when we’re within regular hydrogen peroxide levels. But, it’s not bubbles tickling your back, I’ll just, occasionally, feel them forming on my back, or something came up and I just have one bubble that’s caught and tickling me. I don’t think that’s even that out of the ordinary.
Ashkahn: It’s way more subtle. This is almost continuous while you’re floating. You’re feeling these things, if your levels are too high.
Graham: If you bring it up to 400, 500 parts per million, accidentally, one of your staff drops way too much in there … sometimes, you can actually even see the bubbling in the water itself, visually, which is kind of interesting. Looks like little cauldron brew, or something, in there.
Ashkahn: So, don’t do that.
Graham: Another question, “Is that unsafe?” Are the bubbles a sign that your skin is being eaten by the hydrogen peroxide, or anything crazy like that?
Ashkahn: Not really, that I know of. The other thing that can happen with these levels of peroxide is, you can, very slightly, start to bleach people’s hair, which is another issue. Those are the main reasons people don’t want to go above these 100 limits. I don’t really know, I can’t really speak authoritatively on this, but, people are buying three percent hydrogen peroxide in those brown bottles from the grocery store and gargling with them, and putting them on wounds. Three percent is 30 thousand parts per million, is what that is. I think, even the highest thing I’ve heard tested was 1000 parts per million, and that didn’t seem to do damage to people. But again, don’t take my word for it. It, at least, seems anecdotally out there. It’s not like 100 is a danger zone when these bubbles are forming. I have not heard anything about that actually being a point where this would be harmful to your skin or even if you got it in your eyes, necessarily.
Graham: No real damage that we’ve been able to assess anywhere. As far as we can tell, this is actually the most negative byproduct you get, is, little bubbles and bleaching of the hair.
Ashkahn: Yeah, around that range. That’s why most people stop there. There’s not really … also, as far as I can tell, doesn’t seem like you get a huge benefit from having hydrogen peroxide levels much higher than that. Seems like their ability to oxidize and do the things that they’re doing peter off around 40, 50, 60 parts per million, something like that. You’re not getting a huge bang for your buck by dumping a ton of peroxide into the water.
Graham: Is there anything else that we think is likely to be causing bubbles in someone’s tank? I was trying to think of that while we were talking, and thinking and talking is hard. I decided to do one at a time.
Ashkahn: The bubbles, tiny bubbles, as you’re floating, or something like that, is almost always hydrogen peroxide. The other thing that can cause bubbles is a small leak in your filtration system, right? If you have a pinhole leak in your union. Then when you run your filtration system. Or if your water levels are too low, and your filtration system is sucking air in as you run it … But, that’s real obvious. You run your filtration system, all of a sudden, your whole float tank’s cloudy. It’s been chopped up like a blender, and it gets sent back in. That dissipates pretty quickly, too.
Graham: That’s a problem at the beginning of the float, but not something that would be ongoing. They even say, “small bubbles.”
Ashkahn: Visually, those are so different. Tiny bubbles that are persistent in the water during your float, versus, your whole float tank turns cloudy white for 10 minutes.
Graham: Alright. So, answered?
Ashkahn: I guess so.
Graham: Alright. And that’s our solution for today.
Ashkahn: We’ll talk to you tomorrow.
Graham: Thanks, everyone.
Recent Podcast Episodes
Is it Bad for Float Centers to Always be Running Discounts? – DSP 195
Welcome to the last episode in Social Media Week with Derek, Ashkahn, and Graham. If you haven’t listened to the other episodes in the series, it is strongly recommended that you start at the beginning especially for this episode as it references some points brought up earlier in the week.
Derek and Graham share some more intricacies of the Float On business philosophy and share their opinions on constantly running ads for floats through Groupon or on Social Media. Admittedly, Float On doesn’t run discounts very often, and they share why that is. They also talk about how to run discounts effectively and have a tough conversation about what to do if you want to break that cycle of constant discounts for your floats.
What’s a Reasonable Amount to Spend on Facebook Ads? – DSP 194
Welcome back to Social Media Week!
After talking so much about the fundamentals of social media and its impact on float center marketing, we’re finally able to answer some of the more complex questions that float centers ask. If you haven’t listened to the rest of the Social Media posts from this week, it is strongly recommended you check those out first.
In this episode, Derek provides practical advice for how much to spend on ads for your center, and while each location is going to be different, there are some tried and true tips to follow to help each center find their ideal advertising system.
Choosing Facebook Ad Options for Float Centers – DSP 193
Today on Social Media week, Derek educates Ashkahn and Graham on what exactly it’s like placing an ad on Facebook.
Facebook, as well as other social media sites, provide a cornucopia of options for targeting your ad based on employment, interests, age range, and lots of others. For float centers, this can become fairly confusing, especially since floating doesn’t have demographics in the traditional sense.
Derek clears things up and explains to Graham, Ashkahn, and the rest of the float community, exactly why these options exist and what might work for a specific center.
What the Hell is Facebook Pixel? – DSP 192
Welcome back to Social Media Week!
A Pixel is a tool used when creating an ad account that allows you to create target audiences for your ads. How you use it and what to use it on are more complicated answers though.
Fortunately, Graham and Ashkahn have Derek to use as a resource and they have him break down how best to utilize target audiences and how to get the best bang for your buck.
Can you Cross Post to Different Social Media Platforms? – DSP 191
Today on Social Media Week, Ashkahn and Graham pick Derek’s brain about how to get content for several different social media platforms.
Derek shares his tips for how best to broaden your reach with your social media and not fatigue your audience with the same content on multiple platforms. He also shares what type of content works well on different platforms.
Latest Blog Posts
Finding Funding for Your Float Tank Center
Starting a float center isn’t an inexpensive business opportunity. Depending on the type of float tanks you choose, size of your retail space among other factors, a center can cost between $65-100k per room to fully set up. While centers have started for less money up front, the cost of frequent repairs from salt damage and cutting corners during construction will cost more money in the long run.
Water Hardness in a Float Tank
What is water hardness? Water hardness is, at its most basic, the presence of certain minerals in water. Historically, water hardness was a measure of water’s ability to form lather during laundering. Harder water, due to it’s high calcium/magnesium content, would...
A Blogging Experiment Brought to You By…
At Float Tank Solutions, we're always playing around with different ways to provide benefits to everyone. We've gone a long time actively turning down sponsorship money, to ensure that we stay a source of (as much as is humanly possible) impartial information for...
How To Keep Empty Tanks Warm
The goal of any float center is to never have an empty tank. However, reality says that there will be slow times of the year, last minute cancelations, and unexplained openings in the schedule that will require you to maintain the temperature of an empty tank until...
