Something in the world of floating have you stumped?
Show Highlights
Being able to measure the temperature of your float tank solution is incredibly important, especially since a small variable can make such a huge difference in the variability of the experience. But what kind of thermometer is going to be the most accurate that can still stand up to the demanding environment of a float center? Graham and Ashkahn weigh in.
Show Resources
The Thermoworks Reference Thermometer (Tommy 65,000)
Listen to Just the Audio
Transcription of this episode… (in case you prefer reading)
Graham: Today’s question is, “what type of thermometer do you use?”
Ashkahn: Thermometer.
Graham: Yup. To make the perfect turkey. No, no I assume they mean in your float tank. They didn’t specify.
Ashkahn: Well, we use a handheld thermometer. There’s thermometers in the float tanks, each one it comes with a little thing to tell you the temperature.
Graham: Yeah.
Ashkahn: But, we like having another external handheld thermometer that we use. Because one, we have a variety of models of float tank in our center. So it’s nice for us to have one device we can use from tank to tank, to tank to get a more consistent read out across all of them.
Graham: Yup. It ends up just being nice to also be able to have those around and double check things and just compare. We actually use ones that end up being really precise in their measurements too. So, reference thermometers are actually what they’re called.
We get one that goes down to +/- 0.08 degrees so under point one degrees of accuracy, which often next steps up there get to 0.8 degrees of accuracy is a really common one that you see. At that point it means when you measure you’re within 1.6 degrees of what you think you’re measuring. It’s not a good range, you know.
Ashkahn: What, do you remember? The company’s called ThermoWorks. Do you remember what the actual model of the one we use is?
Graham: Here, I can look it up. Keep … Stall, stall!
Ashkahn: All right. The other nice thing about thermometers is that, if you don’t know if it’s cold or hot, that’s how you figure it out. You use a thermometer. And …
I should say a few things about these thermometers because while we’re tell you the model of the one that we have. It certainly is not perfect. It helps us to be accurate. It breaks on us all the time. It is meant to be kind of water resistant, but it doesn’t seem to be actually able to hold up to the onslaught of water and salt that even when we try to be careful somehow makes its way up the probe into the electronics and eventually they die on us. So, we have two of these one hand at any given point in time because we’re used to one breaking down to the point where we need to send it in for repairs. We’re constantly sending one of these in for repairs.
Graham: Here’s a pro tip too. I recommend naming all of your fragile objects in your shop because it makes people care about them more. This is our theory at least.
Ashkahn: Yeah, we tried naming them. We even tried putting googly eyes on them. Really getting people to have a sentimental attachment to the thermometers so that they wouldn’t be as willing to treat them in a way that would break them, but it still didn’t … If anything it’s made us realize we kill a lot of thermometers. We’ve gone from Tommy to Tuppins to …
Graham: Back to Tommy again.
Ashkahn: Back to Tommy.
Graham: That’s where we are again.
I looked it up. I nailed it before. It’s just their reference thermometer.
Ashkahn: That’s it. It’s just called the ThermoWorks reference thermometer.
Graham: Their handheld reference thermometer, yup.
Ashkahn: Is there like a number? 6500.
Graham: Let’s see. I don’t see a number.
Ashkahn: Okay, well it should be called the 6500. It should have a cool name like that.
Graham: I’ll bring that up with … Here the SKU number’s THS222-555.
Ashkahn: Nice. That sounds way more slick.
Graham: Yeah, it just rolls off the tongue, you know. That’s what we use. We use the THS222-555.
Ashkahn: How much is it?
Graham: Three hundred bucks.
Ashkahn: Three hundred bucks.
Graham: But, the nice thing is when it breaks down, we don’t have to pay that for an entirely new thermometer. We actually just send it back to the company for repairs. Oftentimes it’s the probe that needs to be replaced or the battery pack got corroded. They can just replace those elements.
Ashkahn: For a small fee.
Graham: Like under a hundred bucks, I think.
Ashkahn: But, yeah it still adds up as an expense. It’s a recurring expense for us is keeping working thermometers.
Graham: Yeah. I mean it’s a good lesson I guess, beyond just thermometers too; is not much that’s electronic is long for this world in a float tank center.
Ashkahn: I guess the other thing to mention with thermometers is even if you have the most accurate thermometer in the world you still have to deal with the fact that the water in the float tank might not be uniform. You might be measuring in a spot that is slightly warmer than another spot and it’s not mixed up. Maybe the pump just was running and it heated the water up a little bit. It’s not necessarily the only thing to consider with temperature. There’s just kind of a lot of uncontrollable variables or variables that throw the numbers off a little bit even if you have an incredibly accurate thermometer.
Graham: Yeah, unless you get five of them and make sort of a little grid of probes that you put down across the water at different depths and then write a computer program to kind of take the averages.
Ashkahn: I should say too we have those laser gun thermometers, you know? You know, what I’m talking about?
Graham: Oh, I know what you’re talking about. The old laser therms.
Ashkahn: The laser guns. Those don’t seem to work very well.
Graham: Yeah, at all really.
Ashkahn: We got one and we tested it. They don’t really work at all.
Graham: We actually confirmed that with the ThermoWorks thermometer company as well. You know, they were pretty much saying getting readings off of the water with the refraction of the salt and just everything going on, you’re not going to be able to measure it and they’re not even that accurate.
Ashkahn: No, even for the things they’re meant to be used for, they’re not really like the most accurate of things.
Graham: They measuring ranges of hundreds of degrees for really … When you’re HVAC system heats up and different things like that, not 0.1 degrees.
Ashkahn: So, it’s tempting, once we started breaking these it’s like something that can take a temperature from a distance sounds really great. But, did not seem to actually be the solution.
Graham: Yup. And, definitely if you are choosing out your own thermometer, obviously there’s many companies that offer these, but definitely take a look at that precision amount. In my mind, again anything that’s above 0.1 degrees is a little too high.
All right.
Ashkahn: Done.
Graham: Sha-bam. Thanks for the question and if you have your own, send them to floattanksolutions.com/podcast.
Recent Podcast Episodes
HIPAA Compliance – DSP 330
The Health Insurance Portability and Accountability Act of 1996 (HIPAA) required the Secretary of the U.S. Department of Health and Human Services (HHS) to develop regulations protecting the privacy and security of certain health information. This means that most medical information recorded by healthcare providers has to be stored based on a certain standard of security.
This is only just now becoming an issue in the float industry as centers are starting to accept insurance and medical referrals. However, this is still extremely rare. If this is something that may affect you personally, definitely research additional resources to make sure you’re in compliance.
Getting High (on air) in Float Tanks – DSP 329
Graham and Ashkahn light one up to honestly answer what they think about people coming into float centers high.
The guys share their experiences having Float On share a wall with a dispensary and the number of problems (or lack thereof) that it has caused over the course of many years.
Sit back, grab some munchies, and enjoy the ride with these guys.
What you Need to Know about UV – DSP 328
Have you ever wondered why the UV light on a float tank needs to be replaced so often? If the light is glowing, doesn’t that mean it’s working?
Ashkahn and Graham tackle everything you need to know about UV light, how it works in a float tank, and most importantly, how it can go wrong. This episode is dense with information useful for anyone who uses UV in their float center.
What’s going on with the MAHC? – DSP 327
The Model Aquatic Health Code is a document released by the CDC and has made waves throughout the float industry as this year it included a section on the ideal health department code for float centers as well as pools and spas. Some folks are worried about this because it may mean more rigid and unruly regulations in certain areas.
It’s been a few months since its release, so Graham and Ashkahn give an update to how it has impacted the industry and what it means going forward. Also, Ashkahn learns to abuse the show notes.
Logo Copycats – DSP 326
If you’ve ever looked at a collection of logos from various float centers, they can start to look a little similar. How do you avoid this when designing your own float center logo? Is it a big deal?
Graham and Ashkahn dish on logo design, the importance of simplicity, and a not so subtle reminder that the “don’t be an asshole” rule exists for a reason.
Latest Blog Posts
Should I Have One or Multiple Styles of Float Tank?
If you had every model and type of float tank you’d be running the Burj Khalifa of float centers, with an estimated 38 unique float tanks, which include pods, custom open pools, cabins, vertical tanks, and inflatable or portable float devices currently on the market (not even counting old models).
This is all to say that there are a ton of options out there when considering tanks for your center.
Whether you’re opening a two-tank center, or a bajillion-tank center, do you want all the same model, or will you have some variety?
Why ROI Calculators Suck! (or at least why you should use caution)
“What is an ROI calculator?” I hear you asking. “ROI” simply stands for “Return on Investment”. An “ROI Calculator” is just a tool that outlines the cost of something and generates what your anticipated profit will be over a certain length of time. Usually annually.
We should make a distinction between a simple ROI calculator (i.e. a widget built into a website with limited inputs), and a financial plan (complete with P&L, cashflow, and balance sheets). Both are going to try and do the same thing, but one is going to be far more detailed and accurate.
Roughly what we’re going to be talking about is a return on investment for your whole business, but return on investment can (and should) be used for lots of different aspects to your business to help you determine how best to spend your company’s money. Usually, though, that’s going to require a lot of detail that a simple widget can’t provide.
How to compete on price without slashing prices
Let’s say you’re a float tank center and more centers are starting to show up in your town…
Or, maybe you are that other center starting up a town that already has float tanks…
As new centers enter the market, the typical response is to run promotions on daily deal sites, promote large specials, and/or run Facebook Ads selling floats for much less than the usual offerings.
The best case scenario is this price slashing behavior subsides shortly after the neighboring center opens.
But what if it doesn’t? What if an existing competitor decides their new price is even lower?
How do you compete with a price slashing neighbor without competing on price?
Learn a few ways to make price a non issue with your customers…
Float On’s Halloween Spooktacular!
‘Twas briny, and the epsom groves fluttered with salt-bats, a lurking fog floating atop the murky bog. From the dark maw of silence came a guttural groan, an eerie utterance akin to those of monsters. From the depths of darkness, that groan turned into what mortals...
