Something in the world of floating have you stumped?
Show Highlights
Being able to measure the temperature of your float tank solution is incredibly important, especially since a small variable can make such a huge difference in the variability of the experience. But what kind of thermometer is going to be the most accurate that can still stand up to the demanding environment of a float center? Graham and Ashkahn weigh in.
Show Resources
The Thermoworks Reference Thermometer (Tommy 65,000)
Listen to Just the Audio
Transcription of this episode… (in case you prefer reading)
Graham: Today’s question is, “what type of thermometer do you use?”
Ashkahn: Thermometer.
Graham: Yup. To make the perfect turkey. No, no I assume they mean in your float tank. They didn’t specify.
Ashkahn: Well, we use a handheld thermometer. There’s thermometers in the float tanks, each one it comes with a little thing to tell you the temperature.
Graham: Yeah.
Ashkahn: But, we like having another external handheld thermometer that we use. Because one, we have a variety of models of float tank in our center. So it’s nice for us to have one device we can use from tank to tank, to tank to get a more consistent read out across all of them.
Graham: Yup. It ends up just being nice to also be able to have those around and double check things and just compare. We actually use ones that end up being really precise in their measurements too. So, reference thermometers are actually what they’re called.
We get one that goes down to +/- 0.08 degrees so under point one degrees of accuracy, which often next steps up there get to 0.8 degrees of accuracy is a really common one that you see. At that point it means when you measure you’re within 1.6 degrees of what you think you’re measuring. It’s not a good range, you know.
Ashkahn: What, do you remember? The company’s called ThermoWorks. Do you remember what the actual model of the one we use is?
Graham: Here, I can look it up. Keep … Stall, stall!
Ashkahn: All right. The other nice thing about thermometers is that, if you don’t know if it’s cold or hot, that’s how you figure it out. You use a thermometer. And …
I should say a few things about these thermometers because while we’re tell you the model of the one that we have. It certainly is not perfect. It helps us to be accurate. It breaks on us all the time. It is meant to be kind of water resistant, but it doesn’t seem to be actually able to hold up to the onslaught of water and salt that even when we try to be careful somehow makes its way up the probe into the electronics and eventually they die on us. So, we have two of these one hand at any given point in time because we’re used to one breaking down to the point where we need to send it in for repairs. We’re constantly sending one of these in for repairs.
Graham: Here’s a pro tip too. I recommend naming all of your fragile objects in your shop because it makes people care about them more. This is our theory at least.
Ashkahn: Yeah, we tried naming them. We even tried putting googly eyes on them. Really getting people to have a sentimental attachment to the thermometers so that they wouldn’t be as willing to treat them in a way that would break them, but it still didn’t … If anything it’s made us realize we kill a lot of thermometers. We’ve gone from Tommy to Tuppins to …
Graham: Back to Tommy again.
Ashkahn: Back to Tommy.
Graham: That’s where we are again.
I looked it up. I nailed it before. It’s just their reference thermometer.
Ashkahn: That’s it. It’s just called the ThermoWorks reference thermometer.
Graham: Their handheld reference thermometer, yup.
Ashkahn: Is there like a number? 6500.
Graham: Let’s see. I don’t see a number.
Ashkahn: Okay, well it should be called the 6500. It should have a cool name like that.
Graham: I’ll bring that up with … Here the SKU number’s THS222-555.
Ashkahn: Nice. That sounds way more slick.
Graham: Yeah, it just rolls off the tongue, you know. That’s what we use. We use the THS222-555.
Ashkahn: How much is it?
Graham: Three hundred bucks.
Ashkahn: Three hundred bucks.
Graham: But, the nice thing is when it breaks down, we don’t have to pay that for an entirely new thermometer. We actually just send it back to the company for repairs. Oftentimes it’s the probe that needs to be replaced or the battery pack got corroded. They can just replace those elements.
Ashkahn: For a small fee.
Graham: Like under a hundred bucks, I think.
Ashkahn: But, yeah it still adds up as an expense. It’s a recurring expense for us is keeping working thermometers.
Graham: Yeah. I mean it’s a good lesson I guess, beyond just thermometers too; is not much that’s electronic is long for this world in a float tank center.
Ashkahn: I guess the other thing to mention with thermometers is even if you have the most accurate thermometer in the world you still have to deal with the fact that the water in the float tank might not be uniform. You might be measuring in a spot that is slightly warmer than another spot and it’s not mixed up. Maybe the pump just was running and it heated the water up a little bit. It’s not necessarily the only thing to consider with temperature. There’s just kind of a lot of uncontrollable variables or variables that throw the numbers off a little bit even if you have an incredibly accurate thermometer.
Graham: Yeah, unless you get five of them and make sort of a little grid of probes that you put down across the water at different depths and then write a computer program to kind of take the averages.
Ashkahn: I should say too we have those laser gun thermometers, you know? You know, what I’m talking about?
Graham: Oh, I know what you’re talking about. The old laser therms.
Ashkahn: The laser guns. Those don’t seem to work very well.
Graham: Yeah, at all really.
Ashkahn: We got one and we tested it. They don’t really work at all.
Graham: We actually confirmed that with the ThermoWorks thermometer company as well. You know, they were pretty much saying getting readings off of the water with the refraction of the salt and just everything going on, you’re not going to be able to measure it and they’re not even that accurate.
Ashkahn: No, even for the things they’re meant to be used for, they’re not really like the most accurate of things.
Graham: They measuring ranges of hundreds of degrees for really … When you’re HVAC system heats up and different things like that, not 0.1 degrees.
Ashkahn: So, it’s tempting, once we started breaking these it’s like something that can take a temperature from a distance sounds really great. But, did not seem to actually be the solution.
Graham: Yup. And, definitely if you are choosing out your own thermometer, obviously there’s many companies that offer these, but definitely take a look at that precision amount. In my mind, again anything that’s above 0.1 degrees is a little too high.
All right.
Ashkahn: Done.
Graham: Sha-bam. Thanks for the question and if you have your own, send them to floattanksolutions.com/podcast.
Recent Podcast Episodes
How to Handle Reopening? – DSP 310
If there’s one thing Ashkahn and Graham have learned, it’s reopening. Float On has had to shut down for repairs so many times over the years that they’ve got the process down to a science.
They share their secrets for making sure you have a full week after opening, build momentum, keep your members happy in the downtime and throw a kickin’ reopening party!
What Inspires your Marketing? – DSP 309
Graham and Ashkahn talk about what it’s like when inspiration strikes, how they chase their floaty muse to a solid marketing idea and form it into an actionable plan.
The reality is that it mostly involves a lot of listening and willingness to try, and fail at, new things. As with so many things, play to your strengths, focus on the things you’re passionate about and the rest is practice.
What’s Happening with the Float Conference Non-Profit – DSP 308
Ashkahn and Graham talk about how the Float Conference has been going since they handed off the reigns this year. Big decisions are still incoming, but there’s a lot of ways you can help out or get involved.
If you’d like to offer your help, services, or suggestions for the new Non-profit of the Float Conference, or if you’d just like updates to how it’s going and where it might be held next year, email conference@floathq.com, and the Conference will know to contact you.
VR in a Float Tank – DSP 307
While they haven’t tried it themselves, Ashkahn and Graham liberally distribute their opinions on the use of VR in float tanks and what they think might be better, using it before, after, or during a float.
How to do A/B Testing – DSP 306
A/B Testing is a method to compare one system against another. Most often, this is used to compare the performance of one version of a website to another in real time.
Graham and Ashkahn talk about A/B testing (or “the old onesie-twosies” as Ashkahn says) and how it can be used to improve a float center’s website.
Latest Blog Posts
I’ll Give you a Float Tuesday for a Massage Today: Floating & Bartering
Whoever said that you can’t get something for Nothing obviously never ran a float center. At Float On, we’ve used bartering as a creative means to meet a wide range of goals and needs. Even as I’m writing this, I’m sipping on coffee that we traded from a shop across...
Financing Your Float Center with Investors
In addition to an increase in bank loans, more and more float centers have been using investors in recent years to finance their operations. Every center’s earning potential varies greatly — but a well-run center with no surprise buildout costs (or re-buildout costs) can do very well for itself.
As a result, people with means (or general interest) are increasingly likely to consider having a financial stake in the float industry without the glorious headache of actually running a shop.
Float Conference Interview
In the midst of all of our blog writing and party planning, I sat down with Ashkahn Jahromi, cofounder of The Float Conference, Float On, and Float Tank Solutions with a few questions about the upcoming Float Conference aka #FloatCon for you social media savvy kids in Twitterland.
Take Part in the 2017 Float Industry Report
We’re gathering responses for our 2017 Industry Report through the end of June, and we once again need your help.
Please take a brief moment to answer a few questions about your float center (or future float center) – it may be easiest thing you can do to contribute to the growth of floatation around the world.
