Something in the world of floating have you stumped?
Show Highlights
Being able to measure the temperature of your float tank solution is incredibly important, especially since a small variable can make such a huge difference in the variability of the experience. But what kind of thermometer is going to be the most accurate that can still stand up to the demanding environment of a float center? Graham and Ashkahn weigh in.
Show Resources
The Thermoworks Reference Thermometer (Tommy 65,000)
Listen to Just the Audio
Transcription of this episode… (in case you prefer reading)
Graham: Today’s question is, “what type of thermometer do you use?”
Ashkahn: Thermometer.
Graham: Yup. To make the perfect turkey. No, no I assume they mean in your float tank. They didn’t specify.
Ashkahn: Well, we use a handheld thermometer. There’s thermometers in the float tanks, each one it comes with a little thing to tell you the temperature.
Graham: Yeah.
Ashkahn: But, we like having another external handheld thermometer that we use. Because one, we have a variety of models of float tank in our center. So it’s nice for us to have one device we can use from tank to tank, to tank to get a more consistent read out across all of them.
Graham: Yup. It ends up just being nice to also be able to have those around and double check things and just compare. We actually use ones that end up being really precise in their measurements too. So, reference thermometers are actually what they’re called.
We get one that goes down to +/- 0.08 degrees so under point one degrees of accuracy, which often next steps up there get to 0.8 degrees of accuracy is a really common one that you see. At that point it means when you measure you’re within 1.6 degrees of what you think you’re measuring. It’s not a good range, you know.
Ashkahn: What, do you remember? The company’s called ThermoWorks. Do you remember what the actual model of the one we use is?
Graham: Here, I can look it up. Keep … Stall, stall!
Ashkahn: All right. The other nice thing about thermometers is that, if you don’t know if it’s cold or hot, that’s how you figure it out. You use a thermometer. And …
I should say a few things about these thermometers because while we’re tell you the model of the one that we have. It certainly is not perfect. It helps us to be accurate. It breaks on us all the time. It is meant to be kind of water resistant, but it doesn’t seem to be actually able to hold up to the onslaught of water and salt that even when we try to be careful somehow makes its way up the probe into the electronics and eventually they die on us. So, we have two of these one hand at any given point in time because we’re used to one breaking down to the point where we need to send it in for repairs. We’re constantly sending one of these in for repairs.
Graham: Here’s a pro tip too. I recommend naming all of your fragile objects in your shop because it makes people care about them more. This is our theory at least.
Ashkahn: Yeah, we tried naming them. We even tried putting googly eyes on them. Really getting people to have a sentimental attachment to the thermometers so that they wouldn’t be as willing to treat them in a way that would break them, but it still didn’t … If anything it’s made us realize we kill a lot of thermometers. We’ve gone from Tommy to Tuppins to …
Graham: Back to Tommy again.
Ashkahn: Back to Tommy.
Graham: That’s where we are again.
I looked it up. I nailed it before. It’s just their reference thermometer.
Ashkahn: That’s it. It’s just called the ThermoWorks reference thermometer.
Graham: Their handheld reference thermometer, yup.
Ashkahn: Is there like a number? 6500.
Graham: Let’s see. I don’t see a number.
Ashkahn: Okay, well it should be called the 6500. It should have a cool name like that.
Graham: I’ll bring that up with … Here the SKU number’s THS222-555.
Ashkahn: Nice. That sounds way more slick.
Graham: Yeah, it just rolls off the tongue, you know. That’s what we use. We use the THS222-555.
Ashkahn: How much is it?
Graham: Three hundred bucks.
Ashkahn: Three hundred bucks.
Graham: But, the nice thing is when it breaks down, we don’t have to pay that for an entirely new thermometer. We actually just send it back to the company for repairs. Oftentimes it’s the probe that needs to be replaced or the battery pack got corroded. They can just replace those elements.
Ashkahn: For a small fee.
Graham: Like under a hundred bucks, I think.
Ashkahn: But, yeah it still adds up as an expense. It’s a recurring expense for us is keeping working thermometers.
Graham: Yeah. I mean it’s a good lesson I guess, beyond just thermometers too; is not much that’s electronic is long for this world in a float tank center.
Ashkahn: I guess the other thing to mention with thermometers is even if you have the most accurate thermometer in the world you still have to deal with the fact that the water in the float tank might not be uniform. You might be measuring in a spot that is slightly warmer than another spot and it’s not mixed up. Maybe the pump just was running and it heated the water up a little bit. It’s not necessarily the only thing to consider with temperature. There’s just kind of a lot of uncontrollable variables or variables that throw the numbers off a little bit even if you have an incredibly accurate thermometer.
Graham: Yeah, unless you get five of them and make sort of a little grid of probes that you put down across the water at different depths and then write a computer program to kind of take the averages.
Ashkahn: I should say too we have those laser gun thermometers, you know? You know, what I’m talking about?
Graham: Oh, I know what you’re talking about. The old laser therms.
Ashkahn: The laser guns. Those don’t seem to work very well.
Graham: Yeah, at all really.
Ashkahn: We got one and we tested it. They don’t really work at all.
Graham: We actually confirmed that with the ThermoWorks thermometer company as well. You know, they were pretty much saying getting readings off of the water with the refraction of the salt and just everything going on, you’re not going to be able to measure it and they’re not even that accurate.
Ashkahn: No, even for the things they’re meant to be used for, they’re not really like the most accurate of things.
Graham: They measuring ranges of hundreds of degrees for really … When you’re HVAC system heats up and different things like that, not 0.1 degrees.
Ashkahn: So, it’s tempting, once we started breaking these it’s like something that can take a temperature from a distance sounds really great. But, did not seem to actually be the solution.
Graham: Yup. And, definitely if you are choosing out your own thermometer, obviously there’s many companies that offer these, but definitely take a look at that precision amount. In my mind, again anything that’s above 0.1 degrees is a little too high.
All right.
Ashkahn: Done.
Graham: Sha-bam. Thanks for the question and if you have your own, send them to floattanksolutions.com/podcast.
Recent Podcast Episodes
How do you Start Opening a Float Center? – DSP 285
For people just starting out, it can seem really daunting to start a float center. They may not even know where to begin.
Graham and Ashkahn tackle this idea head on. The most important thing is to do a lot of research (definitely check the resources) and to make sure you have people that you can call and refer to for support when you need it.
What to do When Floaters Interrupt Intros? – DSP 284
Ashkahn’s back and on form. He and Graham take on the question of how to handle first time floaters interrupt the pre-float intros explaining the process.
There’s a lot of information that first time floaters need, and if they aren’t paying attention, it can cause messy floats or unnecessary difficulty or confusion. The reunited duo provides some great tips while going over different customer scenarios.
When is the Best Time to Open a Float Center? – DSP 283
Graham takes the helm again without any co-captain to steer the SS Daily Solutions through the rugged storms of float industry questions.
Today he answers a question about when the best time of year to open your float center. The important thing to remember is that, whenever you choose, you should plan for even earlier, as float centers are more likely to get delayed in construction.
Tips for Choosing Contractors – DSP 282
Graham the Lone Podcaster takes the reigns on answering how to pick a contractor for float center build out.
It’s the kind of big decision that every float center owner hopes to only make once, so getting as much information ahead of time is extremely useful. Graham breaks down some useful tips and explains how to ask for a bid, specific skill sets to look for, and general advice on knowing when to walk away.
Starting your Pumps Early – DSP 281
In this episode, Graham goes solo again to answer a particularly loquacious listener who sent in a question about how to logistically handle your changeover when a floater comes out early.
It can be tempting to start your changeover as soon as possible, especially if you have a few of them to get to, but Graham lays out some helpful things to remember before flipping that switch and running your pumps before the allotted time.
Latest Blog Posts
4,937 Things to Know About Buying a Used Float Tank
You’re thinking about buying a used float tank. Whether this is for a new center, an addition to an existing operation, or a purchase for your home, this is a big decision.
We’ve compiled together some of the major questions and considerations to entertain before making a purchase. While you do have the opportunity to save some money and snag a good deal, there can be hidden costs and unknowns to weigh against those savings.
Offering Overnight Floats
Almost three years ago, we discussed the merits of running overnight floats from an employee’s perspective, focusing on the opportunities of this unique experience as well as its challenges. We’d like to take a deeper dive into this issue because, while the majority of floaters come through our tanks during “normal” business hours, overnight floats form an important part of not only Float On’s identity, but also its business structure and broader culture.
How to Talk About Floating
You step into the elevator and shuffle to the side to make room for the kind-eyed, old woman with the miniature poodle.
“Good morning,” you say with a smile.
“Good morning,” she beams back, her gaze resting briefly on your water bottle with the logo from your float center’s annual party.
After a brief pause, she asks, “What is Float-a-Palooza?”
You take a breath, smile, and launch into your literal elevator pitch.
So, what do you say?
Employee Handbook Template
Whether you are a small or large float center, you most likely have other employees working for you. Regardless of the size of your staff, for reasons of efficiency and legality, it’s essential that your organization has clear and straightforward policies and guidelines. No matter how good employee communication is, it’s always safest and cleanest to have clear parameters and expectations written down.
This is why Float Tank Solutions has created a customizable Employee Handbook Template. Free for anyone to download, it contains federally compliant language (current as of October 2016) and contains a multitude of sections, from employee benefits and compensation descriptions to job guidelines and discrimination policies.
