Something in the world of floating have you stumped?
Show Highlights
Being able to measure the temperature of your float tank solution is incredibly important, especially since a small variable can make such a huge difference in the variability of the experience. But what kind of thermometer is going to be the most accurate that can still stand up to the demanding environment of a float center? Graham and Ashkahn weigh in.
Show Resources
The Thermoworks Reference Thermometer (Tommy 65,000)
Listen to Just the Audio
Transcription of this episode… (in case you prefer reading)
Graham: Today’s question is, “what type of thermometer do you use?”
Ashkahn: Thermometer.
Graham: Yup. To make the perfect turkey. No, no I assume they mean in your float tank. They didn’t specify.
Ashkahn: Well, we use a handheld thermometer. There’s thermometers in the float tanks, each one it comes with a little thing to tell you the temperature.
Graham: Yeah.
Ashkahn: But, we like having another external handheld thermometer that we use. Because one, we have a variety of models of float tank in our center. So it’s nice for us to have one device we can use from tank to tank, to tank to get a more consistent read out across all of them.
Graham: Yup. It ends up just being nice to also be able to have those around and double check things and just compare. We actually use ones that end up being really precise in their measurements too. So, reference thermometers are actually what they’re called.
We get one that goes down to +/- 0.08 degrees so under point one degrees of accuracy, which often next steps up there get to 0.8 degrees of accuracy is a really common one that you see. At that point it means when you measure you’re within 1.6 degrees of what you think you’re measuring. It’s not a good range, you know.
Ashkahn: What, do you remember? The company’s called ThermoWorks. Do you remember what the actual model of the one we use is?
Graham: Here, I can look it up. Keep … Stall, stall!
Ashkahn: All right. The other nice thing about thermometers is that, if you don’t know if it’s cold or hot, that’s how you figure it out. You use a thermometer. And …
I should say a few things about these thermometers because while we’re tell you the model of the one that we have. It certainly is not perfect. It helps us to be accurate. It breaks on us all the time. It is meant to be kind of water resistant, but it doesn’t seem to be actually able to hold up to the onslaught of water and salt that even when we try to be careful somehow makes its way up the probe into the electronics and eventually they die on us. So, we have two of these one hand at any given point in time because we’re used to one breaking down to the point where we need to send it in for repairs. We’re constantly sending one of these in for repairs.
Graham: Here’s a pro tip too. I recommend naming all of your fragile objects in your shop because it makes people care about them more. This is our theory at least.
Ashkahn: Yeah, we tried naming them. We even tried putting googly eyes on them. Really getting people to have a sentimental attachment to the thermometers so that they wouldn’t be as willing to treat them in a way that would break them, but it still didn’t … If anything it’s made us realize we kill a lot of thermometers. We’ve gone from Tommy to Tuppins to …
Graham: Back to Tommy again.
Ashkahn: Back to Tommy.
Graham: That’s where we are again.
I looked it up. I nailed it before. It’s just their reference thermometer.
Ashkahn: That’s it. It’s just called the ThermoWorks reference thermometer.
Graham: Their handheld reference thermometer, yup.
Ashkahn: Is there like a number? 6500.
Graham: Let’s see. I don’t see a number.
Ashkahn: Okay, well it should be called the 6500. It should have a cool name like that.
Graham: I’ll bring that up with … Here the SKU number’s THS222-555.
Ashkahn: Nice. That sounds way more slick.
Graham: Yeah, it just rolls off the tongue, you know. That’s what we use. We use the THS222-555.
Ashkahn: How much is it?
Graham: Three hundred bucks.
Ashkahn: Three hundred bucks.
Graham: But, the nice thing is when it breaks down, we don’t have to pay that for an entirely new thermometer. We actually just send it back to the company for repairs. Oftentimes it’s the probe that needs to be replaced or the battery pack got corroded. They can just replace those elements.
Ashkahn: For a small fee.
Graham: Like under a hundred bucks, I think.
Ashkahn: But, yeah it still adds up as an expense. It’s a recurring expense for us is keeping working thermometers.
Graham: Yeah. I mean it’s a good lesson I guess, beyond just thermometers too; is not much that’s electronic is long for this world in a float tank center.
Ashkahn: I guess the other thing to mention with thermometers is even if you have the most accurate thermometer in the world you still have to deal with the fact that the water in the float tank might not be uniform. You might be measuring in a spot that is slightly warmer than another spot and it’s not mixed up. Maybe the pump just was running and it heated the water up a little bit. It’s not necessarily the only thing to consider with temperature. There’s just kind of a lot of uncontrollable variables or variables that throw the numbers off a little bit even if you have an incredibly accurate thermometer.
Graham: Yeah, unless you get five of them and make sort of a little grid of probes that you put down across the water at different depths and then write a computer program to kind of take the averages.
Ashkahn: I should say too we have those laser gun thermometers, you know? You know, what I’m talking about?
Graham: Oh, I know what you’re talking about. The old laser therms.
Ashkahn: The laser guns. Those don’t seem to work very well.
Graham: Yeah, at all really.
Ashkahn: We got one and we tested it. They don’t really work at all.
Graham: We actually confirmed that with the ThermoWorks thermometer company as well. You know, they were pretty much saying getting readings off of the water with the refraction of the salt and just everything going on, you’re not going to be able to measure it and they’re not even that accurate.
Ashkahn: No, even for the things they’re meant to be used for, they’re not really like the most accurate of things.
Graham: They measuring ranges of hundreds of degrees for really … When you’re HVAC system heats up and different things like that, not 0.1 degrees.
Ashkahn: So, it’s tempting, once we started breaking these it’s like something that can take a temperature from a distance sounds really great. But, did not seem to actually be the solution.
Graham: Yup. And, definitely if you are choosing out your own thermometer, obviously there’s many companies that offer these, but definitely take a look at that precision amount. In my mind, again anything that’s above 0.1 degrees is a little too high.
All right.
Ashkahn: Done.
Graham: Sha-bam. Thanks for the question and if you have your own, send them to floattanksolutions.com/podcast.
Recent Podcast Episodes
When DON’T you Feel Like Floating? – DSP 275
Graham has Juliet on the podcast today since Ashkahn is doing some post-Conference traveling.
The duo talks about times when floating just doesn’t feel like a good idea, which is something they have a bit of disagreement about. Juliet shares her experiences being cautious of her experiences in the tank and how she tends to have to be more mindful of when she floats.
How do you Handle Changing Memberships? – DSP 274
This year at the Float Conference, Derek hosted a marketing forum and took questions that he wanted to share with everyone here.
This episode focuses on how Float On handles memberships, including tiered memberships and how to gracefully transition from one type of membership to another.
Are Vapor Barriers a Good Idea for Float Centers? – DSP 273
You can tell when Graham starts to miss Ashkahn when he makes a soundboard made up of sound clips from previous episodes just to have Ashkahn do another intro.
Jake and Graham break down barriers in this episode. Vapor barriers, that is. These tools are a little confusing in the construction world and their efficacy is hotly debated in just regular construction, never mind the demands that a float center has, especially in regards to moisture protection. Fortunately, Graham and Jake know a thing or two about a thing or two and explain what vapor barriers are, how they work, and what the source of contention is.
What to Consider with Plumbing in a New Float Center – DSP 272
Graham and Jake talk about the confusing world of plumbing for your float center. There are any number of unpleasant surprises that can come about when planning the water lines to showers, getting floor drains in place, and making sure everything lines up how it’s supposed to. If the sewer main is too deep or not where you think it is, it can add a significant amount of cost to your build out just to get floor drains installed. Fortunately, the guys have some useful tricks to help mitigate costs and plan accordingly.
Should I use Spray-in Insulation for my Float Center? – DSP 271
Graham and Jake are still in a sans Ashkahn world at Daily Solutions, but they’re not letting it harsh their mellow.
The guys are talking about the different types of spray-in insulation today. It’s a pretty common material in construction and it can be a fantastic insulator for float centers, if you get the right type.
Jake and Graham go over the differences between open cell and closed cell insulation and why, specifically, float centers should avoid open cell insulation. They also provide some excellent pointers on the materials themselves and good conversations to have with a contractor regarding insulation.
Latest Blog Posts
Oh, the Questions You’ll Hear!
When you run a float tank center, you’re going to get asked a lot of questions. Do I float naked? Can I drown? Is this sanitary? Many of these are easy to answer: It’s recommended. Not without a conscious, and determined effort. Yes! There are some questions, however,...
Happy TANKSgiving (Giving Gifts to Monthly Members)
Monthly memberships are an important way to ensure that your float tank center has a consistent, if not dependable, amount of business.
While pricing structures for memberships vary widely across the industry, we’re focusing less on the strategy of what to charge and looking more at the benefits we’re actually offering. Once we’ve established a solid offering, then we can revisit pricing.
Running a successful monthly membership program takes more than just charging customers and making sure they use their credits. With a little creativity, we can find ways to increase engagement.
Your Flow Meter May Be Inaccurate (and what to do about it)
Float tanks tend to use a lot of parts borrowed from the pool and spa industry and, whenever that happens, it’s always important to question whether that pool part works accurately with our salt water solution. We’ve recently gained some insight into that question on...
The Float Tour Blog Roundup!
The following is our collection of links to the all of the Float Tour blogs. My chronicling of our adventure, highlighting all of you out there.
Thank you for the memories.
