Something in the world of floating have you stumped?
Show Highlights
Being able to measure the temperature of your float tank solution is incredibly important, especially since a small variable can make such a huge difference in the variability of the experience. But what kind of thermometer is going to be the most accurate that can still stand up to the demanding environment of a float center? Graham and Ashkahn weigh in.
Show Resources
The Thermoworks Reference Thermometer (Tommy 65,000)
Listen to Just the Audio
Transcription of this episode… (in case you prefer reading)
Graham: Today’s question is, “what type of thermometer do you use?”
Ashkahn: Thermometer.
Graham: Yup. To make the perfect turkey. No, no I assume they mean in your float tank. They didn’t specify.
Ashkahn: Well, we use a handheld thermometer. There’s thermometers in the float tanks, each one it comes with a little thing to tell you the temperature.
Graham: Yeah.
Ashkahn: But, we like having another external handheld thermometer that we use. Because one, we have a variety of models of float tank in our center. So it’s nice for us to have one device we can use from tank to tank, to tank to get a more consistent read out across all of them.
Graham: Yup. It ends up just being nice to also be able to have those around and double check things and just compare. We actually use ones that end up being really precise in their measurements too. So, reference thermometers are actually what they’re called.
We get one that goes down to +/- 0.08 degrees so under point one degrees of accuracy, which often next steps up there get to 0.8 degrees of accuracy is a really common one that you see. At that point it means when you measure you’re within 1.6 degrees of what you think you’re measuring. It’s not a good range, you know.
Ashkahn: What, do you remember? The company’s called ThermoWorks. Do you remember what the actual model of the one we use is?
Graham: Here, I can look it up. Keep … Stall, stall!
Ashkahn: All right. The other nice thing about thermometers is that, if you don’t know if it’s cold or hot, that’s how you figure it out. You use a thermometer. And …
I should say a few things about these thermometers because while we’re tell you the model of the one that we have. It certainly is not perfect. It helps us to be accurate. It breaks on us all the time. It is meant to be kind of water resistant, but it doesn’t seem to be actually able to hold up to the onslaught of water and salt that even when we try to be careful somehow makes its way up the probe into the electronics and eventually they die on us. So, we have two of these one hand at any given point in time because we’re used to one breaking down to the point where we need to send it in for repairs. We’re constantly sending one of these in for repairs.
Graham: Here’s a pro tip too. I recommend naming all of your fragile objects in your shop because it makes people care about them more. This is our theory at least.
Ashkahn: Yeah, we tried naming them. We even tried putting googly eyes on them. Really getting people to have a sentimental attachment to the thermometers so that they wouldn’t be as willing to treat them in a way that would break them, but it still didn’t … If anything it’s made us realize we kill a lot of thermometers. We’ve gone from Tommy to Tuppins to …
Graham: Back to Tommy again.
Ashkahn: Back to Tommy.
Graham: That’s where we are again.
I looked it up. I nailed it before. It’s just their reference thermometer.
Ashkahn: That’s it. It’s just called the ThermoWorks reference thermometer.
Graham: Their handheld reference thermometer, yup.
Ashkahn: Is there like a number? 6500.
Graham: Let’s see. I don’t see a number.
Ashkahn: Okay, well it should be called the 6500. It should have a cool name like that.
Graham: I’ll bring that up with … Here the SKU number’s THS222-555.
Ashkahn: Nice. That sounds way more slick.
Graham: Yeah, it just rolls off the tongue, you know. That’s what we use. We use the THS222-555.
Ashkahn: How much is it?
Graham: Three hundred bucks.
Ashkahn: Three hundred bucks.
Graham: But, the nice thing is when it breaks down, we don’t have to pay that for an entirely new thermometer. We actually just send it back to the company for repairs. Oftentimes it’s the probe that needs to be replaced or the battery pack got corroded. They can just replace those elements.
Ashkahn: For a small fee.
Graham: Like under a hundred bucks, I think.
Ashkahn: But, yeah it still adds up as an expense. It’s a recurring expense for us is keeping working thermometers.
Graham: Yeah. I mean it’s a good lesson I guess, beyond just thermometers too; is not much that’s electronic is long for this world in a float tank center.
Ashkahn: I guess the other thing to mention with thermometers is even if you have the most accurate thermometer in the world you still have to deal with the fact that the water in the float tank might not be uniform. You might be measuring in a spot that is slightly warmer than another spot and it’s not mixed up. Maybe the pump just was running and it heated the water up a little bit. It’s not necessarily the only thing to consider with temperature. There’s just kind of a lot of uncontrollable variables or variables that throw the numbers off a little bit even if you have an incredibly accurate thermometer.
Graham: Yeah, unless you get five of them and make sort of a little grid of probes that you put down across the water at different depths and then write a computer program to kind of take the averages.
Ashkahn: I should say too we have those laser gun thermometers, you know? You know, what I’m talking about?
Graham: Oh, I know what you’re talking about. The old laser therms.
Ashkahn: The laser guns. Those don’t seem to work very well.
Graham: Yeah, at all really.
Ashkahn: We got one and we tested it. They don’t really work at all.
Graham: We actually confirmed that with the ThermoWorks thermometer company as well. You know, they were pretty much saying getting readings off of the water with the refraction of the salt and just everything going on, you’re not going to be able to measure it and they’re not even that accurate.
Ashkahn: No, even for the things they’re meant to be used for, they’re not really like the most accurate of things.
Graham: They measuring ranges of hundreds of degrees for really … When you’re HVAC system heats up and different things like that, not 0.1 degrees.
Ashkahn: So, it’s tempting, once we started breaking these it’s like something that can take a temperature from a distance sounds really great. But, did not seem to actually be the solution.
Graham: Yup. And, definitely if you are choosing out your own thermometer, obviously there’s many companies that offer these, but definitely take a look at that precision amount. In my mind, again anything that’s above 0.1 degrees is a little too high.
All right.
Ashkahn: Done.
Graham: Sha-bam. Thanks for the question and if you have your own, send them to floattanksolutions.com/podcast.
Recent Podcast Episodes
Should I Wire my Float Tanks into the Wall? – DSP 265
Ashkahn is currently recovering from his talk and the after-party last night, but Jake and Graham have gracefully taken the time to answer a construction question again today.
On the docket today is a question about wiring a float tank directly into the wall. Graham and Jake provide an overview of why some people may prefer this (it’s much easier to keep waterproof, e.g.), and why at Float On they use the twist lock for their outlets and how to properly utilize them.
Can I Keep My Old Ceiling With My Buildout? – DSP 264
Hopefully everyone had a lovely time at the Friday Activities and the after-party.
Ashkahn is still busy running the conference, but Graham and Jake have stepped in to talk about construction!
Today the guys talk about keeping a drop ceiling or T-bar ceiling in an existing space that you’re converting to a float center. The short answer is don’t keep it, as it can cause problems, but the guys do have some workarounds if your landlord is opposed to changing the ceiling.
What to Expect When Expanding from 1 to 3 Tanks? – DSP 263
Ashkahn is busy preparing for everything that happens tonight and tomorrow for the Conference, but that doesn’t mean Daily Solutions will stop being daily.
Graham and Jake talk construction and what to expect when you’re expecting… a giant expansion for your float center. What’s it look like when you go from one tank to three? How do the demands change? What needs to be put in place to make sure that you’re not hitting snags?
Fortunately, these guys know the score and are happy to share.
All About Floor Drains – DSP 262
As Ashkahn gets everything ready for the Start a Center Workshop (happening today) and the Float Conference this weekend, Graham and Jake tackle answering construction questions on the podcast.
Today they’re talking about floor drains. What to consider for drains and how they might pair with different types of flooring. Given the hefty price tag for these more advanced drains, having as much research before making a decision on these is essential. Luckily, the guys have done the hard part already and identified a lot of things to consider.
How to Deal with Float Room Humidity – DSP 261
Graham and Jake are at the helm again while Ashkahn puts the finishing touches on the Float Conference.
Today, the guys are talking all about humidity and how to deal with it when constructing your float rooms. They talk about all the little nuances that you (or your contractor) might not think about when it comes to humidity and how soundproofing and regular airflow may not always go hand in hand.
Latest Blog Posts
The Float Tour Blog – Issue #24
Alberta is often called the Texas of Canada. Part large oil industry, part cattle country.
Don’t Mess With Alberta!
At the base of the Rocky Mountains, replete with an Olympic Stadium, Calgary is a world-class destination for winter sports. The float community developed here similarly to Edmonton – there wasn’t anything nearby except for one or two residential float tanks, and then, in a short period of time, several centers opened all at once. Instead of competing, they’ve decided to work together and have developed one of the tightest knit float communities we’ve seen. They even have monthly Float Dinners, much like we do with the float centers in Portland. They don’t keep meeting minutes, so it’s hard to determine what they talk about at these dinners; my guess would be salt, the effects of salt on various substances, and how salty salt damage can make someone salty.
The Float Tour Blog – Issue #23
After Montana, we blazed our way back into Canada. The drive was long, but the scenery was beautiful. We followed the Rockies north, driving up to Edmonton. It’s a bit of a detour but, there are so many float centers in Edmonton, it seemed crazy not to stop by.
The city itself is primarily made up of workers from the oil fields – high risk, high income jobs that fuel the economy. At least until recently. Our visit was right in the middle of the Fort McMurray wildfire which has displaced a lot of the workforce, forcing 100,000 people to leave their homes. Many came to Edmonton, being the nearest metropolitan area to Fort McMurray. Some already split their time between the two cities, living in Edmonton and traveling to Fort McMurray for weeks or months at a time for work.
It’s understood that, in economic hardship, luxury commodities are typically the first thing people cut back on. Surprisingly, this doesn’t seem to be the case for floating. In fact, more people seem to be trying it to help alleviate the stress, many centers even offering free or discounted services to those displaced in an effort to help in a small way.
The Float Tour Blog – Issue #22
We’ve got two more stops in Colorado Springs before heading west. It’s a town known for its military base and long history of weapons testing. With such a large military presence, it comes as no surprise that the float center owners here are veterans, themselves.
After that, we shoot across to Salt Lake City. Utah is filled with gorgeous sights, from breathtaking lakes to stunning painted hills. With an international landmark famous for its effects on buoyancy, Salt Lake City should be pretty familiar with the concept of floating. With five different float centers, and the manufacturer of the Zen Tent out there, there could be some cause and effect.
After that, we head up into Idaho and Montana to close out the Central United States portion of our Tour. We’ll follow the Rocky Mountains north, taking in the scenery along the way.
The Float Tour Blog – Issue #21
Denver has been home to a vibrant float community for a long time. Some of the earliest commercial centers that started up in the ‘70s and ‘80s were out here. 30 years is a long time, and most of the old centers aren’t around anymore, but there’s a conscious community that has been floating since the old days and they love how much the industry has evolved and grown.
