Something in the world of floating have you stumped?
Show Highlights
Being able to measure the temperature of your float tank solution is incredibly important, especially since a small variable can make such a huge difference in the variability of the experience. But what kind of thermometer is going to be the most accurate that can still stand up to the demanding environment of a float center? Graham and Ashkahn weigh in.
Show Resources
The Thermoworks Reference Thermometer (Tommy 65,000)
Listen to Just the Audio
Transcription of this episode… (in case you prefer reading)
Graham: Today’s question is, “what type of thermometer do you use?”
Ashkahn: Thermometer.
Graham: Yup. To make the perfect turkey. No, no I assume they mean in your float tank. They didn’t specify.
Ashkahn: Well, we use a handheld thermometer. There’s thermometers in the float tanks, each one it comes with a little thing to tell you the temperature.
Graham: Yeah.
Ashkahn: But, we like having another external handheld thermometer that we use. Because one, we have a variety of models of float tank in our center. So it’s nice for us to have one device we can use from tank to tank, to tank to get a more consistent read out across all of them.
Graham: Yup. It ends up just being nice to also be able to have those around and double check things and just compare. We actually use ones that end up being really precise in their measurements too. So, reference thermometers are actually what they’re called.
We get one that goes down to +/- 0.08 degrees so under point one degrees of accuracy, which often next steps up there get to 0.8 degrees of accuracy is a really common one that you see. At that point it means when you measure you’re within 1.6 degrees of what you think you’re measuring. It’s not a good range, you know.
Ashkahn: What, do you remember? The company’s called ThermoWorks. Do you remember what the actual model of the one we use is?
Graham: Here, I can look it up. Keep … Stall, stall!
Ashkahn: All right. The other nice thing about thermometers is that, if you don’t know if it’s cold or hot, that’s how you figure it out. You use a thermometer. And …
I should say a few things about these thermometers because while we’re tell you the model of the one that we have. It certainly is not perfect. It helps us to be accurate. It breaks on us all the time. It is meant to be kind of water resistant, but it doesn’t seem to be actually able to hold up to the onslaught of water and salt that even when we try to be careful somehow makes its way up the probe into the electronics and eventually they die on us. So, we have two of these one hand at any given point in time because we’re used to one breaking down to the point where we need to send it in for repairs. We’re constantly sending one of these in for repairs.
Graham: Here’s a pro tip too. I recommend naming all of your fragile objects in your shop because it makes people care about them more. This is our theory at least.
Ashkahn: Yeah, we tried naming them. We even tried putting googly eyes on them. Really getting people to have a sentimental attachment to the thermometers so that they wouldn’t be as willing to treat them in a way that would break them, but it still didn’t … If anything it’s made us realize we kill a lot of thermometers. We’ve gone from Tommy to Tuppins to …
Graham: Back to Tommy again.
Ashkahn: Back to Tommy.
Graham: That’s where we are again.
I looked it up. I nailed it before. It’s just their reference thermometer.
Ashkahn: That’s it. It’s just called the ThermoWorks reference thermometer.
Graham: Their handheld reference thermometer, yup.
Ashkahn: Is there like a number? 6500.
Graham: Let’s see. I don’t see a number.
Ashkahn: Okay, well it should be called the 6500. It should have a cool name like that.
Graham: I’ll bring that up with … Here the SKU number’s THS222-555.
Ashkahn: Nice. That sounds way more slick.
Graham: Yeah, it just rolls off the tongue, you know. That’s what we use. We use the THS222-555.
Ashkahn: How much is it?
Graham: Three hundred bucks.
Ashkahn: Three hundred bucks.
Graham: But, the nice thing is when it breaks down, we don’t have to pay that for an entirely new thermometer. We actually just send it back to the company for repairs. Oftentimes it’s the probe that needs to be replaced or the battery pack got corroded. They can just replace those elements.
Ashkahn: For a small fee.
Graham: Like under a hundred bucks, I think.
Ashkahn: But, yeah it still adds up as an expense. It’s a recurring expense for us is keeping working thermometers.
Graham: Yeah. I mean it’s a good lesson I guess, beyond just thermometers too; is not much that’s electronic is long for this world in a float tank center.
Ashkahn: I guess the other thing to mention with thermometers is even if you have the most accurate thermometer in the world you still have to deal with the fact that the water in the float tank might not be uniform. You might be measuring in a spot that is slightly warmer than another spot and it’s not mixed up. Maybe the pump just was running and it heated the water up a little bit. It’s not necessarily the only thing to consider with temperature. There’s just kind of a lot of uncontrollable variables or variables that throw the numbers off a little bit even if you have an incredibly accurate thermometer.
Graham: Yeah, unless you get five of them and make sort of a little grid of probes that you put down across the water at different depths and then write a computer program to kind of take the averages.
Ashkahn: I should say too we have those laser gun thermometers, you know? You know, what I’m talking about?
Graham: Oh, I know what you’re talking about. The old laser therms.
Ashkahn: The laser guns. Those don’t seem to work very well.
Graham: Yeah, at all really.
Ashkahn: We got one and we tested it. They don’t really work at all.
Graham: We actually confirmed that with the ThermoWorks thermometer company as well. You know, they were pretty much saying getting readings off of the water with the refraction of the salt and just everything going on, you’re not going to be able to measure it and they’re not even that accurate.
Ashkahn: No, even for the things they’re meant to be used for, they’re not really like the most accurate of things.
Graham: They measuring ranges of hundreds of degrees for really … When you’re HVAC system heats up and different things like that, not 0.1 degrees.
Ashkahn: So, it’s tempting, once we started breaking these it’s like something that can take a temperature from a distance sounds really great. But, did not seem to actually be the solution.
Graham: Yup. And, definitely if you are choosing out your own thermometer, obviously there’s many companies that offer these, but definitely take a look at that precision amount. In my mind, again anything that’s above 0.1 degrees is a little too high.
All right.
Ashkahn: Done.
Graham: Sha-bam. Thanks for the question and if you have your own, send them to floattanksolutions.com/podcast.
Recent Podcast Episodes
Will Hard Water Affect a Float Tank? – DSP 165
Hard water is something that comes from having too many minerals in your water source. It can cause a lot of problems with plumbing if it’s too hard, and most buildings will have resources for dealing with this to help avoid calcium buildup in pipes and along tubs or pools. As for how it interacts with a float tank, specifically, it seems like the larger issue is going to be how it impacts the rest of your building.
Graham and Ashkahn break down what they know about how hard water affects float tanks and the differences you’re going to have to look out for if you’re using well water over municipal water sources.
How do you Know What to Delegate and When? – DSP 164
The eternal small business challenge. You can’t be everywhere at once, but how do you decide what to delegate and to whom? Unfortunately, there’s not an easy solution, but there are some philosophies behind how you run your business and operate that may be helpful to review.
If you’re reaching this wall and you’re not sure what to do, think about how your work is laid out and what is required of you. Some things are naturally going to be more repetitive and have more built in redundancy. That’s a good place to start looking for delegating responsibility, but it doesn’t have to end there. It all just takes time.
Graham and Ashkahn get into the Float On way and how it’s come about that they’re the owners, but don’t run the shop and are no longer making the major decisions in running it as a business. Worth a listen even if you’ve never even seen a float center before.
Float Room Construction Costs Specifics – DSP 163
In this episode, Graham and Ashkahn succinctly breakdown the cost of float room construction. The average float room cost per the industry survey is $75,000 per room. How much of that is float tank cost and how much is construction? There are some variables to consider based on geography and types of tanks, but the guys lay out the average and clarify some of the numbers we’ve released previously.
How to Delicately Handle Difficult Customers – DSP 162
Sometimes there’s just that one customer. The “Problem Child” customer that you don’t like having to deal with. The one who totally know is definitely (probably) making things up to try and get a free float. And they’re such a nuisance! What can you do about that? Obviously you don’t want them getting vengeful if you tell them to kick rocks and spread lies about you.
How do you handle that situation? Well, Graham and Ashkahn lay out some nice ground rules for how they handle people and it comes down to setting clear boundaries that at least appear rigid on the outset. Then, if those boundaries are crossed, the reactions you have are totally expected.
What’s the Difference Between a Residential and Commercial Float Tank? – DSP 161
Ashkahn and Graham break down the differences between float tanks designed for home use in comparison to ones intended for a commercial setting. Depending on how it’s intended to be used can drastically affect the construction of the tank. Most home use tanks, for example, aren’t made of fiberglass, because those large, rigid structures are difficult to move by yourself or just with one other person. Likewise, the filtration demands for a home use tank are a lot different.
Listen in and check out all the differences and which tanks are more intended for use at home as opposed to commercial use.
Latest Blog Posts
Prepayment for Floats
Do you make people pay when they schedule an appointment?
We at Float On always strive to be as easy to deal with and non-intimidating as possible, so from the very beginning we have allowed people to book floats over the phone without payment. READ MORE…
The Difference Between Night and Day
We've all heard the expression, “It’s like the difference between night and day.” The term is used to draw extreme contrast. How much different is our experience of nighttime and daytime? How does it affect how we live? How we work? How we interact with our...
A Peek at the Float On Renovation
Well, we did it again. We've been closed for 2 weeks of construction already, and we still have another week to go. We're installing two new flooring and shower systems to test out, a new lobby wall for soundproofing, and we're replacing one of our Ocean Float Rooms...
The Best Time to Start a Float Center (response)
I usually don't share the responses I get from our posts, but they always spawn great conversations. After this last one, I got hit with more emails than usual, and I wanted to share one of them with you which is representative of many of the others. I've been...
