Something in the world of floating have you stumped?
Show Highlights
Being able to measure the temperature of your float tank solution is incredibly important, especially since a small variable can make such a huge difference in the variability of the experience. But what kind of thermometer is going to be the most accurate that can still stand up to the demanding environment of a float center? Graham and Ashkahn weigh in.
Show Resources
The Thermoworks Reference Thermometer (Tommy 65,000)
Listen to Just the Audio
Transcription of this episode… (in case you prefer reading)
Graham: Today’s question is, “what type of thermometer do you use?”
Ashkahn: Thermometer.
Graham: Yup. To make the perfect turkey. No, no I assume they mean in your float tank. They didn’t specify.
Ashkahn: Well, we use a handheld thermometer. There’s thermometers in the float tanks, each one it comes with a little thing to tell you the temperature.
Graham: Yeah.
Ashkahn: But, we like having another external handheld thermometer that we use. Because one, we have a variety of models of float tank in our center. So it’s nice for us to have one device we can use from tank to tank, to tank to get a more consistent read out across all of them.
Graham: Yup. It ends up just being nice to also be able to have those around and double check things and just compare. We actually use ones that end up being really precise in their measurements too. So, reference thermometers are actually what they’re called.
We get one that goes down to +/- 0.08 degrees so under point one degrees of accuracy, which often next steps up there get to 0.8 degrees of accuracy is a really common one that you see. At that point it means when you measure you’re within 1.6 degrees of what you think you’re measuring. It’s not a good range, you know.
Ashkahn: What, do you remember? The company’s called ThermoWorks. Do you remember what the actual model of the one we use is?
Graham: Here, I can look it up. Keep … Stall, stall!
Ashkahn: All right. The other nice thing about thermometers is that, if you don’t know if it’s cold or hot, that’s how you figure it out. You use a thermometer. And …
I should say a few things about these thermometers because while we’re tell you the model of the one that we have. It certainly is not perfect. It helps us to be accurate. It breaks on us all the time. It is meant to be kind of water resistant, but it doesn’t seem to be actually able to hold up to the onslaught of water and salt that even when we try to be careful somehow makes its way up the probe into the electronics and eventually they die on us. So, we have two of these one hand at any given point in time because we’re used to one breaking down to the point where we need to send it in for repairs. We’re constantly sending one of these in for repairs.
Graham: Here’s a pro tip too. I recommend naming all of your fragile objects in your shop because it makes people care about them more. This is our theory at least.
Ashkahn: Yeah, we tried naming them. We even tried putting googly eyes on them. Really getting people to have a sentimental attachment to the thermometers so that they wouldn’t be as willing to treat them in a way that would break them, but it still didn’t … If anything it’s made us realize we kill a lot of thermometers. We’ve gone from Tommy to Tuppins to …
Graham: Back to Tommy again.
Ashkahn: Back to Tommy.
Graham: That’s where we are again.
I looked it up. I nailed it before. It’s just their reference thermometer.
Ashkahn: That’s it. It’s just called the ThermoWorks reference thermometer.
Graham: Their handheld reference thermometer, yup.
Ashkahn: Is there like a number? 6500.
Graham: Let’s see. I don’t see a number.
Ashkahn: Okay, well it should be called the 6500. It should have a cool name like that.
Graham: I’ll bring that up with … Here the SKU number’s THS222-555.
Ashkahn: Nice. That sounds way more slick.
Graham: Yeah, it just rolls off the tongue, you know. That’s what we use. We use the THS222-555.
Ashkahn: How much is it?
Graham: Three hundred bucks.
Ashkahn: Three hundred bucks.
Graham: But, the nice thing is when it breaks down, we don’t have to pay that for an entirely new thermometer. We actually just send it back to the company for repairs. Oftentimes it’s the probe that needs to be replaced or the battery pack got corroded. They can just replace those elements.
Ashkahn: For a small fee.
Graham: Like under a hundred bucks, I think.
Ashkahn: But, yeah it still adds up as an expense. It’s a recurring expense for us is keeping working thermometers.
Graham: Yeah. I mean it’s a good lesson I guess, beyond just thermometers too; is not much that’s electronic is long for this world in a float tank center.
Ashkahn: I guess the other thing to mention with thermometers is even if you have the most accurate thermometer in the world you still have to deal with the fact that the water in the float tank might not be uniform. You might be measuring in a spot that is slightly warmer than another spot and it’s not mixed up. Maybe the pump just was running and it heated the water up a little bit. It’s not necessarily the only thing to consider with temperature. There’s just kind of a lot of uncontrollable variables or variables that throw the numbers off a little bit even if you have an incredibly accurate thermometer.
Graham: Yeah, unless you get five of them and make sort of a little grid of probes that you put down across the water at different depths and then write a computer program to kind of take the averages.
Ashkahn: I should say too we have those laser gun thermometers, you know? You know, what I’m talking about?
Graham: Oh, I know what you’re talking about. The old laser therms.
Ashkahn: The laser guns. Those don’t seem to work very well.
Graham: Yeah, at all really.
Ashkahn: We got one and we tested it. They don’t really work at all.
Graham: We actually confirmed that with the ThermoWorks thermometer company as well. You know, they were pretty much saying getting readings off of the water with the refraction of the salt and just everything going on, you’re not going to be able to measure it and they’re not even that accurate.
Ashkahn: No, even for the things they’re meant to be used for, they’re not really like the most accurate of things.
Graham: They measuring ranges of hundreds of degrees for really … When you’re HVAC system heats up and different things like that, not 0.1 degrees.
Ashkahn: So, it’s tempting, once we started breaking these it’s like something that can take a temperature from a distance sounds really great. But, did not seem to actually be the solution.
Graham: Yup. And, definitely if you are choosing out your own thermometer, obviously there’s many companies that offer these, but definitely take a look at that precision amount. In my mind, again anything that’s above 0.1 degrees is a little too high.
All right.
Ashkahn: Done.
Graham: Sha-bam. Thanks for the question and if you have your own, send them to floattanksolutions.com/podcast.
Recent Podcast Episodes
What are average floater return rates? – DSP 84
Getting repeat customers is integral to the health of any business. For float centers, this is especially true. It can be worrying when we see our floaters leave the center, never knowing if they’ll return. There’s a very natural inclination to start tracking this trend to see if there’s anything you need to change about your business to attract repeat customers. Memberships are a natural way to attract repeat customers and can quickly become the lifeblood of your center, too.
But how do you measure it? What time frame is acceptable to consider a repeat customer? If they don’t float within six months, does that mean you’ve lost them? If they float once and don’t return for three years, is that a success on your part or a failure?
Graham and Ashkahn tackle all of this and more this time around. Check it out!
How to handle ‘Summer Slump’ in your float center – DSP 83
Many a float center has hit their first summer and seen their schedule thin out. What causes this? Is it just a seasonal thing? What about places that don’t really have seasons? Or tourist towns? What exactly causes this and what are some good tips to combat it? Graham and Ashkahn address this phenomenon head on in this episode.
Addressing customer misinformation – DSP 82
Every float center owner has to deal with customers who get, maybe, a little overenthusiastic about the float experience. What is the best way to deal with customers who say things that are just patently false about the benefits of floating? Do you just let it slide? Do you correct them and potentially offend your customer? It’s not their fault, they’re just excited. It doesn’t seem right to punish them.
This is definitely a tightrope walk type of conversation and it can have an impact on your customers and your reputation as a business, as well as the whole industry. As stewards of the tank, Graham and Ashkahn offer their advice on how best to have this difficult conversation and offer some resources to help with it as well.
Our Report on the Chinese Float Conference – DSP 81
Ashkahn went to China and brought another one of the owners of Float On along, Jake. The two of them share their experiences of visiting the Chinese Float Conference this year and learning about all of the developments in the Chinese float industry, which seems to have exploded in just the last couple of years.
Handling Common Client Concerns: Claustrophobia – DSP 80
This is something pretty much every float center deals with on a regular basis. The first objection that a lot of people will say when they first hear about floating is “Oh, I’m too claustrophobic for that”. Which… feels like getting shut down straight out of the gate.
Graham and Ashkahn, as seasoned float center owners, have heard this all too often and are not only familiar with it, but have some excellent ideas as to why this is the first major objection people throw out there as well as good ways to combat this concern.
Latest Blog Posts
No Results Found
The page you requested could not be found. Try refining your search, or use the navigation above to locate the post.
