Learn best practices for starting and running a float center:
  • This field is for validation purposes and should be left unchanged.

Something in the world of floating have you stumped?

  • This field is for validation purposes and should be left unchanged.

Show Highlights

Graham and Jake are still in a sans Ashkahn world at Daily Solutions, but they’re not letting it harsh their mellow.

The guys are talking about the different types of spray-in insulation today. It’s a pretty common material in construction and it can be a fantastic insulator for float centers, if you get the right type.

Jake and Graham go over the differences between open cell and closed cell insulation and why, specifically, float centers should avoid open cell insulation. They also provide some excellent pointers on the materials themselves and good conversations to have with a contractor regarding insulation.

Show Resources

Listen to Just the Audio

Transcription of this episode… (in case you prefer reading)

Graham: All right. Welcome everybody to our podcast.

Jake: Thank you for joining us.

Graham: I am Graham.

Jake: I am Jake.

Graham: I thought you were going to say, “I am Ashkahn.” I’m like so used to hearing that.

Jake: I thought about it.

Graham: Okay, all right. So today’s question is, “What about spray-in insulation? My contractor recommended it for the building I’m moving into, which is on the older side.”

Jake: Hmm, the building is on the older side.

Graham: I assume not the spray-in insulation-

Jake: Yeah.

Graham: Or the contractor.

Jake: Yeah, I know, right? What’s with this insulation? All right, so I guess we’re talking about on-site spray-in polyurethane, like foam insulation.

Graham: Yeah, so I guess first of all, you can spray almost anything, right?

Jake: Yeah, like you can do blow-in of-

Graham: Denim.

Jake: Roxul, or like rock wool. Like denim, it was a bad idea for a float center-

Graham: It’s a terrible idea-

Jake: Like anything coarse. Like, don’t blow in cellulose. Don’t do those things. It would just retain moisture. If you are going to do a blow-in, like if you have like little crevices and stuff like that, stick to the stone wall blow-in and stuff like that.

Graham: So yeah, let’s assume, I mean, obviously, they’re probably insulating it for thermal barriers-

Jake: Yeah. It’s an older building, they’re drafty. I bet that’s what they’re talking about. I think that’s what they’re talking about.

Graham: Lots of weird joists and stuff-

Jake: Yeah-

Graham: It’s just like weird little-

Jake: Old conduits.

Graham: Areas-

Jake: Yeah.

Graham: Where they’re trying to use something that isn’t spray-in-

Jake: Nooks.

Graham: It’s going to take a ton of time-

Jake: Or crannies. Yeah.

Graham: To have everything.

Jake: Because you got to get it efficient. You don’t want any gaps, basically, like a two percent gap-

Graham: Yeah.

Jake: 20 percent heat loss. So everything should be form fit to your area. If they’re doing bats, and there’s a lot of little nooks, that’s going to be labor intensive.

Graham: Either really hard or impossible-

Jake: Yeah.

Graham: Or just incredibly expensive.

Jake: So, what some people do with older buildings, more single story buildings, where like the top is, it’s like a hot place, or something like that. They will do an on-site application of a polyurethane foam insulation, basically spraying that into the joist base. And it expands. Then it also tightens up the structure, as well. Like, it does serve to tighten up the structure because it expands into every little nook and cranny, which means you’re getting less permeability, less air moving from within a space, and then from the outside of space as well. We do have a distinction here, though. Open cell versus closed cell polyurethane on-site application foam sprays.

Graham: Right, and I was going to say it’s actually the closed cell that does more of the tightening up of the structure, right?

Jake: It does, yeah. It does.

Graham: Like, that’s more of the structural, the structural insulation?

Jake: Yeah, it’s tighter, it blocks more moisture. It’s actually kind of like what we recommend for float centers. So, open cell is a little bit better at blocking out noise.

Graham: And just to backup a little bit, you could almost guess what this means with open cell versus closed cell insulation-

Jake: Right.

Graham: But, it’s basically just the open cell has kind of expanded-

Jake: Fractures.

Graham: Yeah.

Jake: Yeah.

Graham: It’s expanded, there’s little kind of air bubbles in there. Like, it’s an open kind of structure.

Jake: Yeah, air bubbles that pop. So like part circle and then part gash, and real porous. It’s good for thermal resistance and everything like that.

Graham: Good for soundproofing.

Jake: Yeah, good for soundproofing. The problem for us and some southern humid states, is that moisture will pass through it and then get stuck on the substrate. So, moisture will pass through insulation, and then get stuck on the underside of your roof, or get stuck on the underside of whatever. And that’s a problem for float centers. So we definitely say stick to the closed cell. And the closed cell, those bubbles just don’t pop. They’re still expanding. Those gases are inside there, but it’s just a thick, solid layer, so moisture can’t really pass through there.

Graham: Which means it’s not going to as a good job sound proofing, because it will just be kind of rigid and transmit a lot of vibrations-

Jake: Yeah, vibrations.

Graham: Vibrational noise. But it does do a much better job solidifying your structure-

Jake: Yeah.

Graham: Because I have this very tight, solid spray-in that’s-

Jake: Everything is trade offs, right.

Graham: Yeah, yeah, yeah.

Jake: It’s all trade offs.

Graham: But specifically for a float center, we kind of don’t even get to think about the trade offs on the good side for open cell insulation just because I mean, it’s so humid. The chances that you’re going to get mold when you do open cell spray-in insulation are just too high.

Jake: Just too high of risk.

Graham: Why risk it?

Jake: Yeah. And this is something that you hire a talented contractor to do. One, because again, you don’t want them to do poorly. And two, the stuff is pretty bad for your health.

Graham: It’s crazy.

Jake: You don’t really want to be in this space when people are doing it.

Graham: They go to like full almost like Hazmat suits-

Jake: Oh, yeah. For sure.

Graham: Your entire-

Jake: Respirators.

Graham: Your entire building is kind of also in a Hazmat suit-

Jake: Yeah, yeah.

Graham: Because if that settles anywhere, it really sticks to it-

Jake: Good reason to be in good communication with your contractor, your general, just making sure that you’re not showing up right after that happened.

Graham: Yeah, it would be terrible, for example, if you accidentally blew expanding foam over into your neighbor’s space-

Jake: Yeah.

Graham: While they were giving a haircut or something like that.

Jake: Mm-hmm.

Graham: Not that we’d know anything about-

Jake: Yeah, and then foam got all over their fancy vest-

Graham: Yeah.

Jake: And their hat. And then we had to buy that for them.

Graham: Yeah, that’d be terrible. You definitely should really be careful with the contractors installing things.

Jake: I will say, that hole no longer exists, for what it’s worth.

Graham: It’s true.

Jake: For what it’s worth.

Graham: Yeah, no we discovered some more places where we could tighten up our own construction as a result of that, yeah.

Jake: Yeah.

Graham: Okay, so spray-in insulation totally makes sense.

Jake: Yep.

Graham: You were closed cell spray-in insulation.

Jake: Mm-hmm. And whenever I’m saying “spray-in” usually on exterior walls or ceilings, you know what I mean? Like we don’t see that a lot in between float rooms, you know what I mean?

Graham: Ah. Good point.

Jake: Yeah.

Graham: yeah, I was assuming that it was going to be on the ceiling-

Jake: Right, yeah. I’m always making these assumptions, and I’m like, “Wait a minute. Is everyone on the same-“

Graham: So, yeah. And the exterior wall, of course, is just a little more important for the stuff because you have the entire environment out there.

Jake: Mm-hmm, yeah.

Graham: So the amount of-

Jake: You’ve got a conditioned space, you have an unconditioned space.

Graham: Yeah, so getting that barrier, and yeah getting some kind of insulation up is really critical. Older buildings-

Jake: Mm-hmm.

Graham: You know, if they did have good insulation at one point, it’s almost certainly gone. They might not have had it to begin with.

Jake: Yeah, and we’ve seen people that have skimmed on some things. Like they’ve cut back a little bit on that exterior insulation, not on the outside of the building, but those exterior walls, and that’s where you see moisture damage. That’s where you see peeling, that’s where you see panels de-laminating from all the like. Every wall is fine except for this wall, and it’s like, well that’s your exterior wall. You should have figured that out. You should have insulated that a little better. You know? You’ve got two more inches in the room, but now you’re dealing with this constant problem.

Graham: So yeah, no and it makes total sense to me. I think your contractor’s recommendation is-

Jake: Yeah.

Graham: Without looking deeply at the plans in your actual building, it definitely makes sense. And I can understand why a contractor would recommend spray-in insulation. Maybe mention to them that you’d like closed cell, if they weren’t planning on it.

Jake: Definitely mention it to them.

Graham: Yeah. Yeah, if they know it’s a humid environment and all the details of your float center, they’re probably already planning on that anyway.

Jake: Be sure to be hip to it, though. Just check. No matter what.

Graham: Always check, yeah.

Jake: Yeah, always check. And on the very likely chance that we’re wrong, and you were talking about like you wanted to blow-in some denim. Don’t.

Graham: Yeah, don’t.

Jake: Don’t do it.

Graham: Yeah, for the same reason, but even more so that you don’t want the open cell insulation-

Jake: Yeah.

Graham: Which is just anything that can collect that moisture-

Jake: Yep.

Graham: Anything that’s permeable at all. It’s just –

Jake: Mold or mildew.

Graham: Yeah, you’re asking for-

Jake: That’s another whole thing-

Graham: Issues.

Jake: You know what I mean, the polyurethane? No food. No mold. No mildew. So, all right cool. Yeah. All right, thanks for submitting that question. I really appreciate it. Long question, short answer. Sorry for that. But if you guys have more questions for us, please send those in at FloatTankSolutions.com/Podcast, and thanks for spending this time for us today. All right, so back to yoga?

Graham: Goodbye everyone.

Recent Podcast Episodes

Being the First Float Center – DSP 320

What’s it like to be the first float center to open in an area? How do you handle it? 

Graham and Ashkahn explain what it was like opening Float On, being one of the first dedicated float centers in the United States. The exciting thing is that creating awareness is really fun, but it can be a little stressful since your float center will represent floating as a practice for people.

Many of the tips here are the same for anyone opening a center: focus on awareness, be prepared to educate, and make sure your floats are the best they can be.

What you Need to Know About Algorithms – DSP 318

Ashkahn and Derek talk about algorithms, those pesky bits of code that push your posts up or down on social media and search engines and leave you scrambling for ways to get likes and clicks, constantly mixing it up to just be seen. 

The duo discusses how algorithms affect everyday posts for small businesses and how to keep up on information about the constantly changing nature of these systems. The main takeaway is, if your content is fresh, non-repetitive and you aren’t trying to game the system, you likely have nothing to worry about.

Commissions for Memberships? – DSP 317

Any sales related business knows that commissions are the gold-standard incentive program for drumming up business, but how does it work in a float center for memberships?

Derek and Ashkahn talk about the mixed success they’ve experienced at Float On each time it’s been tried. 

Getting Members to Float More Often – DSP 316

Single float memberships have become increasingly more common in the float industry, typically with the option to purchase additional floats for the month at a discount. But how do you properly incentivize those members to float more than a single time per month? 

Ashkahn and Derek talk marketing tips to keeping your float center top of mind and making sure your members are active regularly. 

Latest Blog Posts

How Many Float Tanks Should I Have?

How Many Float Tanks Should I Have?

Intro If you’ve crossed over into the sacred realm of “Yeah, I’m pretty sure I’m gonna open up a float center,” an obvious question arises — “How many tanks should I have?” Now, if you’re like me, you’re creating a 90 tank float community where everyone who buys in...

The Construction Secret to Soundproofing: Storage Between Float Rooms

The Construction Secret to Soundproofing: Storage Between Float Rooms

If you’ve ever taken a look at our construction materials or gotten advice on soundproofing, you’ve probably heard of the importance of including “air gaps” when building out your center. What that means and why it helps can be a bit of a technical question, and the practical implementation can seem daunting and unreasonable.  

Float Conference 2017 Recap

Float Conference 2017 Recap

Now that the salt has settled, I’m sharing some thoughts from “The Great Gathering of People Who Really Love Being Alone Sometimes in a Dark, Briny Room,” also known as The Float Conference.

The conference has always been an amazing opportunity to connect with the pulse of the broader float industry and, if this year’s gathering showed us anything, it’s that our collective heartbeat is as strong as ever.

2017 Float Conference Program Introduction

2017 Float Conference Program Introduction

Every year, I have the great pleasure of writing the introduction for the Float Conference program, and every year we share it on our blog so that members of the industry who weren’t able to make the journey out to Portland are able to check it out. I hope you enjoy reading it as much as I enjoyed writing it.

From all of us at Float Tank Solutions, where our time is measured as the space between two conferences, thank you again for a wonderful year!

– Graham Talley