Learn best practices for starting and running a float center:
  • This field is for validation purposes and should be left unchanged.

Something in the world of floating have you stumped?

  • This field is for validation purposes and should be left unchanged.

Show Highlights

Graham and Jake are still in a sans Ashkahn world at Daily Solutions, but they’re not letting it harsh their mellow.

The guys are talking about the different types of spray-in insulation today. It’s a pretty common material in construction and it can be a fantastic insulator for float centers, if you get the right type.

Jake and Graham go over the differences between open cell and closed cell insulation and why, specifically, float centers should avoid open cell insulation. They also provide some excellent pointers on the materials themselves and good conversations to have with a contractor regarding insulation.

Show Resources

Listen to Just the Audio

Transcription of this episode… (in case you prefer reading)

Graham: All right. Welcome everybody to our podcast.

Jake: Thank you for joining us.

Graham: I am Graham.

Jake: I am Jake.

Graham: I thought you were going to say, “I am Ashkahn.” I’m like so used to hearing that.

Jake: I thought about it.

Graham: Okay, all right. So today’s question is, “What about spray-in insulation? My contractor recommended it for the building I’m moving into, which is on the older side.”

Jake: Hmm, the building is on the older side.

Graham: I assume not the spray-in insulation-

Jake: Yeah.

Graham: Or the contractor.

Jake: Yeah, I know, right? What’s with this insulation? All right, so I guess we’re talking about on-site spray-in polyurethane, like foam insulation.

Graham: Yeah, so I guess first of all, you can spray almost anything, right?

Jake: Yeah, like you can do blow-in of-

Graham: Denim.

Jake: Roxul, or like rock wool. Like denim, it was a bad idea for a float center-

Graham: It’s a terrible idea-

Jake: Like anything coarse. Like, don’t blow in cellulose. Don’t do those things. It would just retain moisture. If you are going to do a blow-in, like if you have like little crevices and stuff like that, stick to the stone wall blow-in and stuff like that.

Graham: So yeah, let’s assume, I mean, obviously, they’re probably insulating it for thermal barriers-

Jake: Yeah. It’s an older building, they’re drafty. I bet that’s what they’re talking about. I think that’s what they’re talking about.

Graham: Lots of weird joists and stuff-

Jake: Yeah-

Graham: It’s just like weird little-

Jake: Old conduits.

Graham: Areas-

Jake: Yeah.

Graham: Where they’re trying to use something that isn’t spray-in-

Jake: Nooks.

Graham: It’s going to take a ton of time-

Jake: Or crannies. Yeah.

Graham: To have everything.

Jake: Because you got to get it efficient. You don’t want any gaps, basically, like a two percent gap-

Graham: Yeah.

Jake: 20 percent heat loss. So everything should be form fit to your area. If they’re doing bats, and there’s a lot of little nooks, that’s going to be labor intensive.

Graham: Either really hard or impossible-

Jake: Yeah.

Graham: Or just incredibly expensive.

Jake: So, what some people do with older buildings, more single story buildings, where like the top is, it’s like a hot place, or something like that. They will do an on-site application of a polyurethane foam insulation, basically spraying that into the joist base. And it expands. Then it also tightens up the structure, as well. Like, it does serve to tighten up the structure because it expands into every little nook and cranny, which means you’re getting less permeability, less air moving from within a space, and then from the outside of space as well. We do have a distinction here, though. Open cell versus closed cell polyurethane on-site application foam sprays.

Graham: Right, and I was going to say it’s actually the closed cell that does more of the tightening up of the structure, right?

Jake: It does, yeah. It does.

Graham: Like, that’s more of the structural, the structural insulation?

Jake: Yeah, it’s tighter, it blocks more moisture. It’s actually kind of like what we recommend for float centers. So, open cell is a little bit better at blocking out noise.

Graham: And just to backup a little bit, you could almost guess what this means with open cell versus closed cell insulation-

Jake: Right.

Graham: But, it’s basically just the open cell has kind of expanded-

Jake: Fractures.

Graham: Yeah.

Jake: Yeah.

Graham: It’s expanded, there’s little kind of air bubbles in there. Like, it’s an open kind of structure.

Jake: Yeah, air bubbles that pop. So like part circle and then part gash, and real porous. It’s good for thermal resistance and everything like that.

Graham: Good for soundproofing.

Jake: Yeah, good for soundproofing. The problem for us and some southern humid states, is that moisture will pass through it and then get stuck on the substrate. So, moisture will pass through insulation, and then get stuck on the underside of your roof, or get stuck on the underside of whatever. And that’s a problem for float centers. So we definitely say stick to the closed cell. And the closed cell, those bubbles just don’t pop. They’re still expanding. Those gases are inside there, but it’s just a thick, solid layer, so moisture can’t really pass through there.

Graham: Which means it’s not going to as a good job sound proofing, because it will just be kind of rigid and transmit a lot of vibrations-

Jake: Yeah, vibrations.

Graham: Vibrational noise. But it does do a much better job solidifying your structure-

Jake: Yeah.

Graham: Because I have this very tight, solid spray-in that’s-

Jake: Everything is trade offs, right.

Graham: Yeah, yeah, yeah.

Jake: It’s all trade offs.

Graham: But specifically for a float center, we kind of don’t even get to think about the trade offs on the good side for open cell insulation just because I mean, it’s so humid. The chances that you’re going to get mold when you do open cell spray-in insulation are just too high.

Jake: Just too high of risk.

Graham: Why risk it?

Jake: Yeah. And this is something that you hire a talented contractor to do. One, because again, you don’t want them to do poorly. And two, the stuff is pretty bad for your health.

Graham: It’s crazy.

Jake: You don’t really want to be in this space when people are doing it.

Graham: They go to like full almost like Hazmat suits-

Jake: Oh, yeah. For sure.

Graham: Your entire-

Jake: Respirators.

Graham: Your entire building is kind of also in a Hazmat suit-

Jake: Yeah, yeah.

Graham: Because if that settles anywhere, it really sticks to it-

Jake: Good reason to be in good communication with your contractor, your general, just making sure that you’re not showing up right after that happened.

Graham: Yeah, it would be terrible, for example, if you accidentally blew expanding foam over into your neighbor’s space-

Jake: Yeah.

Graham: While they were giving a haircut or something like that.

Jake: Mm-hmm.

Graham: Not that we’d know anything about-

Jake: Yeah, and then foam got all over their fancy vest-

Graham: Yeah.

Jake: And their hat. And then we had to buy that for them.

Graham: Yeah, that’d be terrible. You definitely should really be careful with the contractors installing things.

Jake: I will say, that hole no longer exists, for what it’s worth.

Graham: It’s true.

Jake: For what it’s worth.

Graham: Yeah, no we discovered some more places where we could tighten up our own construction as a result of that, yeah.

Jake: Yeah.

Graham: Okay, so spray-in insulation totally makes sense.

Jake: Yep.

Graham: You were closed cell spray-in insulation.

Jake: Mm-hmm. And whenever I’m saying “spray-in” usually on exterior walls or ceilings, you know what I mean? Like we don’t see that a lot in between float rooms, you know what I mean?

Graham: Ah. Good point.

Jake: Yeah.

Graham: yeah, I was assuming that it was going to be on the ceiling-

Jake: Right, yeah. I’m always making these assumptions, and I’m like, “Wait a minute. Is everyone on the same-“

Graham: So, yeah. And the exterior wall, of course, is just a little more important for the stuff because you have the entire environment out there.

Jake: Mm-hmm, yeah.

Graham: So the amount of-

Jake: You’ve got a conditioned space, you have an unconditioned space.

Graham: Yeah, so getting that barrier, and yeah getting some kind of insulation up is really critical. Older buildings-

Jake: Mm-hmm.

Graham: You know, if they did have good insulation at one point, it’s almost certainly gone. They might not have had it to begin with.

Jake: Yeah, and we’ve seen people that have skimmed on some things. Like they’ve cut back a little bit on that exterior insulation, not on the outside of the building, but those exterior walls, and that’s where you see moisture damage. That’s where you see peeling, that’s where you see panels de-laminating from all the like. Every wall is fine except for this wall, and it’s like, well that’s your exterior wall. You should have figured that out. You should have insulated that a little better. You know? You’ve got two more inches in the room, but now you’re dealing with this constant problem.

Graham: So yeah, no and it makes total sense to me. I think your contractor’s recommendation is-

Jake: Yeah.

Graham: Without looking deeply at the plans in your actual building, it definitely makes sense. And I can understand why a contractor would recommend spray-in insulation. Maybe mention to them that you’d like closed cell, if they weren’t planning on it.

Jake: Definitely mention it to them.

Graham: Yeah. Yeah, if they know it’s a humid environment and all the details of your float center, they’re probably already planning on that anyway.

Jake: Be sure to be hip to it, though. Just check. No matter what.

Graham: Always check, yeah.

Jake: Yeah, always check. And on the very likely chance that we’re wrong, and you were talking about like you wanted to blow-in some denim. Don’t.

Graham: Yeah, don’t.

Jake: Don’t do it.

Graham: Yeah, for the same reason, but even more so that you don’t want the open cell insulation-

Jake: Yeah.

Graham: Which is just anything that can collect that moisture-

Jake: Yep.

Graham: Anything that’s permeable at all. It’s just –

Jake: Mold or mildew.

Graham: Yeah, you’re asking for-

Jake: That’s another whole thing-

Graham: Issues.

Jake: You know what I mean, the polyurethane? No food. No mold. No mildew. So, all right cool. Yeah. All right, thanks for submitting that question. I really appreciate it. Long question, short answer. Sorry for that. But if you guys have more questions for us, please send those in at FloatTankSolutions.com/Podcast, and thanks for spending this time for us today. All right, so back to yoga?

Graham: Goodbye everyone.

Recent Podcast Episodes

Monthly Budget for Float Centers – DSP 305

Graham and Ashkahn break down the real truth about how closely they watch their budget for Float On on  a monthly basis. 

The truth is… not much. As it turns out, monthly expenses for float centers don’t have huge variations unlike businesses that rely on retail, for example. Graham and Ashkahn explain they developed a sense for what’s within reason. 

How to Sign on Float Ambassadors – DSP 304

How to Sign on Float Ambassadors – DSP 304

Float Ambassadors have been with the industry since the beginning, but gained popularity sometime in the last few years. What are ambassadors and how to float centers find them? When they do find them, how do they get them to represent floating? 

Graham and Ashkahn share their experiences with the practice of finding float mavens out in the world and the impact they’ve had on Float On. 

How do you Talk about Psychedelics? – DSP 303

It’s no secret that the inventor of the float tank, John Lilly, was also an early psychonaut and used the tank for mental exploration in conjunction with LSD. Not everyone in the float community appreciates this shared history and some actively try to distance themselves from it given the taboo nature of psychedelics. 

Graham and Ashkahn share their thoughts on psychedelics and floating and how, as a business, they can be completely separated while still being important, as well as explaining why some people might reasonably decide to disassociate from them. 

What About 75 Minute Floats? – DSP 302

Most float centers divide on floats offered between 60 or 90 minute floats, but some split the difference right down the middle and offer 75 minutes. Graham and Ashkahn share their thoughts on this tactic, what they see as the pros, cons, and things to consider when implementing it. 

Free Floats for Teachers – DSP 301

Graham and Ashkahn give their perspective on the pros and cons of giving free floats away for teachers. Giving out free floats is the Float On way and giving them to a specific group of people who could really use them sounds like a good idea.

The guys break it down and address some of the concerns any float center may have about running a program like this.

Latest Blog Posts

The Basics of Float Tank Sanitation

The Basics of Float Tank Sanitation

Some of the most common questions you’ll get as a float center operator involve the cleanliness of the tanks. This post will be an introduction to some of the most commonplace sanitation methods used in float tanks. These are generally either chemicals that go in the water or devices that attach to your filtration system. We’ll be discussing chlorine, bromine, ozone, UV, and hydrogen peroxide, which accounts for the sanitation methods used on nearly every float tank on the market.

Testing and Maintaining Float Tank Water Quality

Testing and Maintaining Float Tank Water Quality

Editors Note: This is a revision of a past blog post, updated to reflect the most current sanitation methods and standards

 

In a perfect world, you could just pour water and salt into a float tank and it would stay pure and clean and fresh and salty forever. In the real world, conditions in the water are constantly changing, so keeping your water safe and clean takes a fair amount of vigilance.

This post covers how we maintain basic water quality in the float tank, except for sanitization methods, which will be covered in their own beastly sanitation blog post. Stay tuned for that coming out next week!

Floating, mental health, and wellness

Floating, mental health, and wellness

This post will explore the intersection of floating with the concepts, beliefs, and experiences related to mental health and wellness, with a focus on anxiety and depression. I’ll explore my own story as it relates to floating before diving into the current intersections of floating and mental health, with a look at past, current, and potential opportunities for research and personal growth.

Massage, Acupuncture, and Float Tanks…  A Chat with Sandra Calm

Massage, Acupuncture, and Float Tanks… A Chat with Sandra Calm

We’ve seen lots of float centers that aren’t just float centers.

Many have massage, some offer counseling, some have yoga classes next door. Lots of people start out either by incorporating float tanks into a larger business, or with float tanks only being one of many modalities at their center. Being specialists in floating, Float On has not mastered anything else.

So, to help gain insight into this growing aspect of the industry, we contacted our old friend, Sandra Calm. She started up The Float Shoppe here in Portland with her husband and podcast sensation, Dylan Calm, back in 2011. When they first opened, they had just two float tanks, and slowly added acupuncture, massage, counseling, along with two more tanks. Talk about expansion!

She was more than happy to take some time for the industry to help us understand just what it’s like to run a center with multiple services by answering some questions.