Something in the world of floating have you stumped?
Show Highlights
Graham and Jake are still in a sans Ashkahn world at Daily Solutions, but they’re not letting it harsh their mellow.
The guys are talking about the different types of spray-in insulation today. It’s a pretty common material in construction and it can be a fantastic insulator for float centers, if you get the right type.
Jake and Graham go over the differences between open cell and closed cell insulation and why, specifically, float centers should avoid open cell insulation. They also provide some excellent pointers on the materials themselves and good conversations to have with a contractor regarding insulation.
Show Resources
Listen to Just the Audio
Transcription of this episode… (in case you prefer reading)
Graham: All right. Welcome everybody to our podcast.
Jake: Thank you for joining us.
Graham: I am Graham.
Jake: I am Jake.
Graham: I thought you were going to say, “I am Ashkahn.” I’m like so used to hearing that.
Jake: I thought about it.
Graham: Okay, all right. So today’s question is, “What about spray-in insulation? My contractor recommended it for the building I’m moving into, which is on the older side.”
Jake: Hmm, the building is on the older side.
Graham: I assume not the spray-in insulation-
Jake: Yeah.
Graham: Or the contractor.
Jake: Yeah, I know, right? What’s with this insulation? All right, so I guess we’re talking about on-site spray-in polyurethane, like foam insulation.
Graham: Yeah, so I guess first of all, you can spray almost anything, right?
Jake: Yeah, like you can do blow-in of-
Graham: Denim.
Jake: Roxul, or like rock wool. Like denim, it was a bad idea for a float center-
Graham: It’s a terrible idea-
Jake: Like anything coarse. Like, don’t blow in cellulose. Don’t do those things. It would just retain moisture. If you are going to do a blow-in, like if you have like little crevices and stuff like that, stick to the stone wall blow-in and stuff like that.
Graham: So yeah, let’s assume, I mean, obviously, they’re probably insulating it for thermal barriers-
Jake: Yeah. It’s an older building, they’re drafty. I bet that’s what they’re talking about. I think that’s what they’re talking about.
Graham: Lots of weird joists and stuff-
Jake: Yeah-
Graham: It’s just like weird little-
Jake: Old conduits.
Graham: Areas-
Jake: Yeah.
Graham: Where they’re trying to use something that isn’t spray-in-
Jake: Nooks.
Graham: It’s going to take a ton of time-
Jake: Or crannies. Yeah.
Graham: To have everything.
Jake: Because you got to get it efficient. You don’t want any gaps, basically, like a two percent gap-
Graham: Yeah.
Jake: 20 percent heat loss. So everything should be form fit to your area. If they’re doing bats, and there’s a lot of little nooks, that’s going to be labor intensive.
Graham: Either really hard or impossible-
Jake: Yeah.
Graham: Or just incredibly expensive.
Jake: So, what some people do with older buildings, more single story buildings, where like the top is, it’s like a hot place, or something like that. They will do an on-site application of a polyurethane foam insulation, basically spraying that into the joist base. And it expands. Then it also tightens up the structure, as well. Like, it does serve to tighten up the structure because it expands into every little nook and cranny, which means you’re getting less permeability, less air moving from within a space, and then from the outside of space as well. We do have a distinction here, though. Open cell versus closed cell polyurethane on-site application foam sprays.
Graham: Right, and I was going to say it’s actually the closed cell that does more of the tightening up of the structure, right?
Jake: It does, yeah. It does.
Graham: Like, that’s more of the structural, the structural insulation?
Jake: Yeah, it’s tighter, it blocks more moisture. It’s actually kind of like what we recommend for float centers. So, open cell is a little bit better at blocking out noise.
Graham: And just to backup a little bit, you could almost guess what this means with open cell versus closed cell insulation-
Jake: Right.
Graham: But, it’s basically just the open cell has kind of expanded-
Jake: Fractures.
Graham: Yeah.
Jake: Yeah.
Graham: It’s expanded, there’s little kind of air bubbles in there. Like, it’s an open kind of structure.
Jake: Yeah, air bubbles that pop. So like part circle and then part gash, and real porous. It’s good for thermal resistance and everything like that.
Graham: Good for soundproofing.
Jake: Yeah, good for soundproofing. The problem for us and some southern humid states, is that moisture will pass through it and then get stuck on the substrate. So, moisture will pass through insulation, and then get stuck on the underside of your roof, or get stuck on the underside of whatever. And that’s a problem for float centers. So we definitely say stick to the closed cell. And the closed cell, those bubbles just don’t pop. They’re still expanding. Those gases are inside there, but it’s just a thick, solid layer, so moisture can’t really pass through there.
Graham: Which means it’s not going to as a good job sound proofing, because it will just be kind of rigid and transmit a lot of vibrations-
Jake: Yeah, vibrations.
Graham: Vibrational noise. But it does do a much better job solidifying your structure-
Jake: Yeah.
Graham: Because I have this very tight, solid spray-in that’s-
Jake: Everything is trade offs, right.
Graham: Yeah, yeah, yeah.
Jake: It’s all trade offs.
Graham: But specifically for a float center, we kind of don’t even get to think about the trade offs on the good side for open cell insulation just because I mean, it’s so humid. The chances that you’re going to get mold when you do open cell spray-in insulation are just too high.
Jake: Just too high of risk.
Graham: Why risk it?
Jake: Yeah. And this is something that you hire a talented contractor to do. One, because again, you don’t want them to do poorly. And two, the stuff is pretty bad for your health.
Graham: It’s crazy.
Jake: You don’t really want to be in this space when people are doing it.
Graham: They go to like full almost like Hazmat suits-
Jake: Oh, yeah. For sure.
Graham: Your entire-
Jake: Respirators.
Graham: Your entire building is kind of also in a Hazmat suit-
Jake: Yeah, yeah.
Graham: Because if that settles anywhere, it really sticks to it-
Jake: Good reason to be in good communication with your contractor, your general, just making sure that you’re not showing up right after that happened.
Graham: Yeah, it would be terrible, for example, if you accidentally blew expanding foam over into your neighbor’s space-
Jake: Yeah.
Graham: While they were giving a haircut or something like that.
Jake: Mm-hmm.
Graham: Not that we’d know anything about-
Jake: Yeah, and then foam got all over their fancy vest-
Graham: Yeah.
Jake: And their hat. And then we had to buy that for them.
Graham: Yeah, that’d be terrible. You definitely should really be careful with the contractors installing things.
Jake: I will say, that hole no longer exists, for what it’s worth.
Graham: It’s true.
Jake: For what it’s worth.
Graham: Yeah, no we discovered some more places where we could tighten up our own construction as a result of that, yeah.
Jake: Yeah.
Graham: Okay, so spray-in insulation totally makes sense.
Jake: Yep.
Graham: You were closed cell spray-in insulation.
Jake: Mm-hmm. And whenever I’m saying “spray-in” usually on exterior walls or ceilings, you know what I mean? Like we don’t see that a lot in between float rooms, you know what I mean?
Graham: Ah. Good point.
Jake: Yeah.
Graham: yeah, I was assuming that it was going to be on the ceiling-
Jake: Right, yeah. I’m always making these assumptions, and I’m like, “Wait a minute. Is everyone on the same-“
Graham: So, yeah. And the exterior wall, of course, is just a little more important for the stuff because you have the entire environment out there.
Jake: Mm-hmm, yeah.
Graham: So the amount of-
Jake: You’ve got a conditioned space, you have an unconditioned space.
Graham: Yeah, so getting that barrier, and yeah getting some kind of insulation up is really critical. Older buildings-
Jake: Mm-hmm.
Graham: You know, if they did have good insulation at one point, it’s almost certainly gone. They might not have had it to begin with.
Jake: Yeah, and we’ve seen people that have skimmed on some things. Like they’ve cut back a little bit on that exterior insulation, not on the outside of the building, but those exterior walls, and that’s where you see moisture damage. That’s where you see peeling, that’s where you see panels de-laminating from all the like. Every wall is fine except for this wall, and it’s like, well that’s your exterior wall. You should have figured that out. You should have insulated that a little better. You know? You’ve got two more inches in the room, but now you’re dealing with this constant problem.
Graham: So yeah, no and it makes total sense to me. I think your contractor’s recommendation is-
Jake: Yeah.
Graham: Without looking deeply at the plans in your actual building, it definitely makes sense. And I can understand why a contractor would recommend spray-in insulation. Maybe mention to them that you’d like closed cell, if they weren’t planning on it.
Jake: Definitely mention it to them.
Graham: Yeah. Yeah, if they know it’s a humid environment and all the details of your float center, they’re probably already planning on that anyway.
Jake: Be sure to be hip to it, though. Just check. No matter what.
Graham: Always check, yeah.
Jake: Yeah, always check. And on the very likely chance that we’re wrong, and you were talking about like you wanted to blow-in some denim. Don’t.
Graham: Yeah, don’t.
Jake: Don’t do it.
Graham: Yeah, for the same reason, but even more so that you don’t want the open cell insulation-
Jake: Yeah.
Graham: Which is just anything that can collect that moisture-
Jake: Yep.
Graham: Anything that’s permeable at all. It’s just –
Jake: Mold or mildew.
Graham: Yeah, you’re asking for-
Jake: That’s another whole thing-
Graham: Issues.
Jake: You know what I mean, the polyurethane? No food. No mold. No mildew. So, all right cool. Yeah. All right, thanks for submitting that question. I really appreciate it. Long question, short answer. Sorry for that. But if you guys have more questions for us, please send those in at FloatTankSolutions.com/Podcast, and thanks for spending this time for us today. All right, so back to yoga?
Graham: Goodbye everyone.
Recent Podcast Episodes
Should Float Centers use Light or Heavy Gauge Studs? – DSP 269
Still no Ashkahn today. He’s taking a couple of post-conference days to himself.
Jake and Graham are on the scene though to answer construction questions, though. Even the straight forward ones, like today. Jake informs us which to choose when doing construction, light or heavy gauge studs when constructing a float center, while getting a little sidetracked when comparing wooden and metal studs.
Construction to Make Your Life Easier – DSP 268
Graham and Jake cover a wide range of construction tips to make running a float center easier. Everything from making sure you have extra storage to installing mop closets with sinks in them for dealing with heavy duty chemicals.
The advice is pretty much a shotgun approach of tips, tricks, and hard lessons learned throughout the years.
Draining Float Tanks into Septic Systems – DSP 267
Graham and Jake tackle the difficulties of draining float tanks and how that process can differ based on different municipalities, different water treatment systems, or whether you’re using a septic system or not.
Water treatment typically involves whole contained ecosystems and highly concentrated epsom salt water can impact that pretty drastically. The guys provide good tips for each type of system and what to be prepared for if you’re operating in a rural area with a septic system.
The Difference Between STC and Decibels – DSP 266
Post-Conference Ashkahn is still out of the recording studio, but fortunately Jake is keeping Graham company in there.
Graham and Jake break down the differences between decibels and STC ratings, two very important to understand when figuring out soundproofing. There’s a lot to digest in this episode, but fortunately the guys keep it easy to understand by providing a broad level overview of the different concepts.
Should I Wire my Float Tanks into the Wall? – DSP 265
Ashkahn is currently recovering from his talk and the after-party last night, but Jake and Graham have gracefully taken the time to answer a construction question again today.
On the docket today is a question about wiring a float tank directly into the wall. Graham and Jake provide an overview of why some people may prefer this (it’s much easier to keep waterproof, e.g.), and why at Float On they use the twist lock for their outlets and how to properly utilize them.
Latest Blog Posts
The Float Tour Blog – Issue #28
Home sweet home! After so many months on the road, it was strange being back here in Portland. We were exhausted, excited, and a little travel weary. The first night back, I slept in my own bed for the first time in three months and the world just melted away.
Having travelled across the United States, I’m reminded of how insular Portland is. We are aggressively fixated on keeping things local. Local beer, ketchup, bikes, pet food, pillows, phone cases… it’s part of our charm. We want to reward people for living here and being a part of the community. It’s so pervasive that, after living here for so long, I kind of forgot that Secret Aardvark hot-sauce isn’t available everywhere, and that most cities don’t even recycle, let alone compost.
The Float Tour Blog – Issue #27
Our northern neighbor – a sister city, of sorts – Seattle is the largest metropolitan area in the Pacific Northwest. It’s the land of Microsoft and Kurt Cobain, and the culture here embraces both simultaneously. It’s tech business professional in the front and rock n’ roll grunge in the back. This blend creates a perfect storm of high energy business life and high energy nightlife, making relaxation a valuable commodity. Floating helps fill the void left by nightmarish traffic and overcrowded restaurants.
Given that it’s so close to home, the float centers in Seattle are a lot more familiar to us. Our visits here were more like a high school reunion than they were like the first day of school. During some of our visits, we were picking up conversations right where we left them.
The Float Tour Blog Issue #26
Vancouver is the largest metropolitan area in Canada, and third largest on the West Coast. It’s a major hub for international trade, with one of the largest ports in the world, giving it a large migrant population, mainly from Asia, the Middle East, and Australia. It’s also been a long-time home to the Canadian film industry, and has even been nicknamed “North Hollywood.” Dozens of film and television productions from major studios film here every year.
Vancouver is very much an international city. It has large boroughs dedicated to varying cultures, including one of the largest Chinatowns in the world. The society here is more receptive to new ideas, always looking for the next big thing; it’s not surprising that floating has blown up in Vancouver as much as it has.
In the last 3 years, 10 float centers have opened up, most of them being larger 4–6 tank centers. The really interesting thing is how they all opened within the same short amount of time about 1 ½ to 2 years ago, within months of each other.
The Float Tour Blog – Issue #25
We finally made it back to the West Coast! We went through the Canadian Rockies and were overwhelmed by the beauty of it all. We drove through hours and hours of winding mountain roads, fertile valleys, and tiny towns so picturesque they looked like movie sets. It was so captivating, in fact, I suspect Graham and Ashkahn may have secretly replaced themselves with robotic doppelgängers to hike throughout Banff.
This post will focus on the smaller communities in B.C. that are bringing floating to new people every day. We also get to visit Canadian manufacturer Pro Float. They’re relatively new to the scene, just opening up earlier this year – another exciting sign of the growth in the industry.